THINFAX 288C modem/telephone/ISDN Settings and Configuration

Card Type	Modem (synchronous/asynchronous)
Chipset	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis
Fax Class	Class I & II
Data Bus	PCMCIA Type II

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \G, \K, \N

%C, %E, %L, %Q, %TT

Special AT Commands

#CID, :E, *H, -K, )M, @M, +MS, -Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92

S95, S99, S201

Note: See MHI help file for complete information.

UNIDENTIFIED COMMANDS
Command	Default
S37	0
S80	0

AUTOSYNC OPTIONS
Type:		Register
Format		AT [cmds] S19=n [cmds]
Default:		26
Range:		0 - 30
Description:		Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle.
Bit	Value	Function
0	0	Not used
1	0 í 1	Binary synchronous protocol used. HDLC protocol used.
2	í 0 1	HDLC address detect disabled. HDLC address detect enabled.
3	0 í 1	NRZI bit coding used. NRZ bit coding used.
4	0 í 1	HDLC idle sends MARK. HDLC idle sends FLAG or SYNC.

AUTOSYNC HDLC ADDRESS
Type:	Register
Format:	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	Sets the HDLC address and binary synchronous character.

CELLULAR DRIVER DOWNLOAD
Type:	Immediate
Format:	AT [cmds] ^C2 [cmds]
Description:	Downloads a cellular phone driver.

CELLULAR STATUS
Type:			Immediate
Format:			AT [cmds] ^T6 [cmds]
Default:			Read-only
Range:			0 - 191
Description:			Indicates the status of cellular phone.
Bit	Value			Function
0	0 1			Cellular phone is not receiving a call. Cellular phone is receiving a call.
1		0 1			Cellular phone is not in use. Cellular phone is in use.
2		0 1			Cellular phone is not locked. Cellular phone is locked.
3		0 1			Cellular service detected. Cellular service not detected.
4		0 1			Cellular phone is powered off. Cellular phone is powered on.
5		0 1			Cellular driver is initialized. Cellular driver is not initialized.
6		0			Not used.
7		0 1			Cellular cable not detected. Cellular cable detected.

DISPLAY CELLULAR DRIVER INFORMATION
Type:	Immediate
Format:	AT [cmds] ^I [cmds]
Description:	Displays information about the current cellular driver.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested about the modem.
Command	Function
I0	Displays product identification code.
I1	Displays ROM checksum.
I2	Reports OK
I3	Displays firmware model, revision, and interface type.
I4	Displays OEM response.
I5	Displays country code.
I6	Displays data pump model.
I7	Displays DAA code.

REMOTE CONFIGURATION CHARACTER
Type:	Register
Format:	AT [cmds] S202=n [cmds]
Default:	170
Range:	0 - 255
Unit:	1 ASCII character
Description:	Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character.