COLUMBUS 28.8 LAN + MODEM COMBO modem/telephone/ISDN Settings and Configuration
EMPOWER LABS, INC.
COLUMBUS 28.8 LAN + MODEM COMBO
Card Type | Modem (asynchronous), Ethernet |
Chipset | Unidentified |
Network Transfer Rate | 10Mbps |
Maximum Data Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | PCMCIA Type II |
Fax Class | Class I & II |
Data Modulation | Bell 103A/212A ITU-T V.22, V.22bis, V.23, V.23bis, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation | ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression | MNP5, MNP10EC, V.42, V.42bis |
Topology | Linear Bus/Star |
Wire Type | Unshielded twisted pair RG-58A/U 50ohm coaxial |
Boot ROM | Not available |
EMPOWER-LABS-INC-Modem-asynchronous-Ethernet-COLUM
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &Q, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \J, \K, \L, \N |
%C, %E, %TT |
Special AT Commands |
:E, *H, -K, )M, @M, +MS, -Q |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
S26, S28, S29, S30, S32, S33, S36, S38, S39, S40, S46, S48, S82, S86, S91, S92, S95, S201 |
Note: See MHI documentation for complete information. |
UNIDENTIFIED COMMANDS | |
Command | Default |
S27 | 73 |
S31 | 198 |
S37 | 0 |
S41 | 195 |
Proprietary AT Command Set
CELLULAR STATUS INDICATOR | |||||
Format: | AT [cmds] ^T6 [cmds] | ||||
Default: | Read only | ||||
Range: | 0-255 | ||||
Description: | Indicates the status of cellular phone. | ||||
Bit | Value | Function | |||
0 | 0 1 | Cellular phone is not receiving a call. Cellular phone is receiving a call. | |||
1 | 0 1 | Cellular phone is not in use. Cellular phone is in use. | |||
2 | 0 1 | Cellular phone is not locked. Cellular phone is locked. | |||
3 | 0 1 | Cellular service detected. Cellular service not detected. | |||
4 | 0 1 | Cellular phone is powered off. Cellular phone is powered on. | |||
5 | 0 1 | Cellular driver is initialized. Cellular driver is not initialized. | |||
6 | 0 | Not used. | |||
7 | 0 1 | Land line detected. Cellular cable detected. | |||
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D <#> [cmds] |
Description: | Dials the telephone number indicated according to any modifiers included in the string. |
Command | Function |
DJ | MNP10 link will be negotiated at 1200bps for this call. |
DK | MNP10 power level adjustment enabled for this call. |
DL | Re-dial last number. |
DP | Pulse dialing enabled. |
DS=n | Dial stored telephone number n. |
DT | Tone dialing enabled. |
DW | Dialing resumed following dial tone detection. |
D, | Dialing paused for amount of time specified in S8 register. |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D^ | Calling tone disabled for this call. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
DISPLAY CELLULAR DRIVER | |
Type: | Immediate |
Format: | AT [cmds] ^I [cmds] |
Description: | Displays cellular phone driver information. |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] I4 [cmds] |
Description: | Reports the product identification string. |
My Books
