2400BPS EXTERNAL MNP MODEM modem/telephone/ISDN Settings and Configuration

Card Type	Modem (synchronous/asynchronous)
Chip Set	Unidentified
Maximum Data Rate	2400bps
Data Bus	External
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis
Error Correction/Compression	MNP5, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line in		CN1		DC power		CN4
Line out		CN2		Power switch		SW1
RS-232/422		CN3

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
HS	Red	On	Modem is operating at 1200bps or faster
HS	Red	Off	Modem is operating at slower than 1200bps
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
AA	Red	Blinking	Phone is ringing
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
MR	Red	On	Power is on
MR	Red	Off	Power is off
MR	Red	Blinking	Modem in test mode

ACCEPT RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \U [cmds]
Description:	Accept remote modem’s request for reliable mode

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	Unidentified
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character; %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

BIT MAPPED REGISTERS
Register	Default
S14	Unidentified
S21	Unidentified
S22	Unidentified
S23	Unidentified
S27	Unidentified

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE Reliable/Normal mode		Break from DTE Direct mode	Break received from remote modem	Modem receives \B
\K0	Online command mode enabled, send no break to remote modem		Online command mode enabled, send break to remote modem immediately	Buffers cleared, break sent to DTE	Break sent to remote modem and buffers cleared
\K1	Break sent to remote modem and buffers cleared		Send break to remote modem immediately	Buffers cleared, break sent to DTE	Break sent to remote modem and buffers cleared
\K2	Online command mode enabled, send no break to remote modem		Online command mode enabled, send break to remote modem immediately	Break sent immediately to DTE	Send break to remote modem immediately
\K3	Send break to remote modem immediately		Send break to remote modem immediately	Break sent immediately to DTE	Send break to remote modem immediately
\K4	Online command mode enabled, send no break to remote modem		Online command mode enabled, send break to remote modem immediately	Break sent with received data to the DTE	Send break with transmitted data
í \K5	Send break with transmitted data		Send break to remote modem immediately	Break sent with received data to the DTE	Send break with transmitted data

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
í \N1	Direct mode enabled
\N2	MNP reliable mode enabled
\N3	Auto-reliable mode enabled

CONVERT TO RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \Y [cmds]
Description:	Converts to reliable mode from normal or direct mode

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Modifier	Function
P	Pulse dialing enabled
R	Answer mode enabled, originate mode disabled following handshake initiation
Sn	Dial stored telephone number n
T	Tone dialing enabled
W	Dialing resumed following dial tone detection
,	Dialing paused for amount of time specified in S8 register
!	Modem commanded to go off-hook for specified time before returning on-hook
@	Wait for quiet answer
;	Modem returned to command state after dialing

DISPLAY CONFIGURATION
Type:	Immediate
Format:	AT [cmds] \S [cmds]
Description:	Displays current modem settings

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Select standard or extended result codes
Command	Function
\V0	Standard result codes enabled
\V1	Extended result codes enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
í \Q0	Flow control disabled
\Q1	XON/XOFF flow control enabled
\Q2	CTS flow control by DCE enabled
\Q3	RTS/CTS flow control enabled

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects. \T0 will disable timer.

INITIATE RELIABLE MODE
Type:	Immediate
Format:	AT [cmds] \O [cmds]
Description:	Initiates reliable mode from normal or direct mode

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
\J0	Serial speed locked
í \J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

MNP - STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP link
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	34/66ms at 10pps (British)

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem code
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports version information

STORE TELEPHONE NUMBER
Type:	Configuration
Format:	AT [cmds] &Zn=(phone # & modifiers)
Description:	Writes selected telephone numbers into the non-volatile memory at location n
Note:	The characters described in the D command are valid for use in the &Z command; telephone numbers and modifiers can include up to 30 characters.

SWITCH TO NORMAL MODE
Type:	Immediate
Format:	AT [cmds] \Z [cmds]
Description:	Switches to normal mode from MNP mode

TEST MODES
Type:		Register
Format:		AT [cmds] S16=n [cmds]
Default:		0
Range:		0-125
Unit:		Bit-mapped
Description:		Controls loopback tests: analog, digital, remote digital, and self tests
Bit	Value	Function
0	í 0 1	Local analog loopback not in progress Local analog loopback in progress
1	í 0	Not used
2	í 0 1	Local digital loopback not in progress Local digital loopback in progress
3	í 0 1	Modem not in remote digital loopback Remote digital loopback in progress
4	í 0 1	Remote digital loopback not requested Remote digital loopback requested
5	í 0 1	Remote digital loopback w/ self-test not in progress Remote digital loopback w/ self-test in progress
6	í 0 1	Local analog loopback w/ self-test not in progress Local analog loopback w/ self-test in progress

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
í \X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem