MVP144XV2 modem/telephone/ISDN Settings and Configuration

CONNECTIONS
Purpose	Location	Purpose	Location
Line out	CN1	DC power	CN4
Line in	CN2	Volume	R1
RS-232/422	CN3	Power switch	SW1

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
RI	Red	Blinking	Phone is ringing
RI	Red	Off	Phone not ringing
CD	Red	Blinking	Modem is retraining
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
RD	Red	On	Modem is receiving data
RD	Red	Off	Modem is not receiving data
SD	Red	On	Modem is transmitting data
SD	Red	Off	Modem is not transmitting data
TR	Red	On	DTR signal is high
TR	Red	Off	DTR signal is low
MR	Red	On	Modem is ready
MR	Red	Off	Modem not ready

AUTO-RETRAIN - FALLBACK/FALLFORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Example:	AT %E2 <CR>
Description:	Controls auto-retrain mode and fallback/fall forward.
Command	Function
%E0	Auto-retrain disabled.
%E1	Auto-retrain enabled.
» %E2	Fallback/fall forward enabled.

BIT-MAPPED REGISTERS
Register	Default
S14	138
S16	0
S21	52
S22	117
S23	62
S27	73
S28	0
S31	194
S39	3
S40	104
S41	195

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Example:	AT \B3 &W<CR>
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem.

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Example:	AT \K5 <CR>
Description:	Configures action of break signal.
Command		Break from DTE Reliable/Normal mode	Modem receives \B	Break from remote modem
\K0		Enter command mode, do not send break to remote modem.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K1		Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K2		Enter command mode, do not send break to remote modem.	Send break to remote modem immediately.	Send break to DTE immediately.
\K3		Send break to remote modem immediately.	Send break to remote modem immediately.	Send break to DTE immediately.
\K4		Enter command mode, do not send break to remote modem.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.
» \K5		Send break with transmitted data.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.

COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :En [cmds]
Example:	AT :E1 &W<CR>
Description:	Controls V.32 compromise equalizer.
Command	Function
:E0	Equalizer disabled.
» :E1	Equalizer enabled.

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Example:	AT \N1 DT555-1212<CR>
Description:	Sets connect mode.
Command	Function
\N0	Normal mode.
\N1	Direct mode.
\N2	Reliable mode.
\N3	Auto-reliable mode.
\N4	V.42 reliable mode.
\N5	MNP error correction mode.

COMPRESSION
Type:	Configuration
Format:	AT %Cn
Example:	AT *EC0 %C1 *AP0<CR>
Description:	Selects data compression.
Command	Function
%C0	Data compression disabled.
%C1	MNP5 enabled.
%C2	V.42bis enabled.
» %C3	MNP5 and V.42bis enabled.

EXTENDED RING
Format:		AT [cmds] -SDR=n [cmds]
Example:		AT-SDR=3<CR>
Default:		0
Range:		0 - 7
Unit:		Bit-mapped
Description:		Selects the response to extended ring types.
Bit	Value		Function
0	» 0 1		Do not respond to ring type 1. Respond to ring type 1.
1	» 0 1		Do not respond to ring type 2. Respond to ring type 2.
2	» 0 1		Do not respond to ring type 3. Respond to ring type 3.

FLASH DIAL MODIFIER TIME
Format	AT [cmds] S29=n [cmds]
Example:	ATS29=0<CR>
Default:	0
Range:	0-255
Unit:	.01 second
Description:	Time the modem will go on-hook upon receiving the ! dial modifier in dial string.

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S33=n [cmds]
Example:	ATS33=20<CR>
Default:	19
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF.

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S32=n [cmds]
Example:	ATS32=20<CR>
Default:	17
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON.

LINE SIGNAL LEVEL
Type:	Configuration
Format:	AT [cmds] %L [cmds]
Example:	AT %L &W<CR>
Description:	Returns recieved line signal level.

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Example:	AT \A1 %C1<CR>
Description:	Sets the maximum transmittable block size.
Command	Function
\A0	MNP block size is 64 characters.
» \A1	MNP block size is 128 characters.
\A2	MNP block size is 192 characters.
\A3	MNP block size is 256 characters.

MNP10 TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] -SECn,a [cmds]
Example:	AT-SEC1,24<CR>
Default:	Unidentified
Range:	a=0-30
Unit:	-1 dBm
Description:	Enables/disables and sets the transmission level for MNP10.
Command	Function
n=0	MNP10 disabled.
n=1	MNP10 enabled.

MODE SELECTION
Type:	Immediate
Format:	AT [cmds] +FCLASS=n [cmds]
Example:	AT +FCLASS=0 &W<CR>
Description:	Sets what mode the modem will operate in.
Command	Function
+FCLASS=0	Data mode enabled.
+FCLASS=1	Fax mode enabled.
+FCLASS=80	Voice mode enabled.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Example:	AT I1 O<CR>
Description:	Displays modem properties.
Command	Function
I0	Reports product code.
I1	Reports firmware checksum.
I2	Reports firmware checksum result. (Report OK if correct)
I3	Reports firmware revision.
I4	Reports identifier string.
I5	Reports country code.
I6	Reports Data Pump modem and revision.

REPORT SIGNAL QUALITY
Type:	Configuration
Format:	AT [cmds] %Q [cmds]
Example:	AT %Q &W<CR>
Description:	Reports signal quality.

SLEEP TIMER
Format	AT [cmds] S24=n [cmds]
Example:	ATS24=40<CR>
Default:	0
Range:	0 - 255
Unit:	1 second
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.

TRANSMISSION LEVEL
Type:	Configuration
Format:	AT [cmds] @Mn [cmds]
Example:	AT @M25 &W<CR>
Default:	0
Range:	11-30
Unit:	-1 dBm
Description:	Sets the signal level for transmission.
Command	Function
» @M0	-26dBm
@M1	-30dBm
@M2-@M10	-10dBm