CARDINAL TECHNOLOGIES, INC.
MB14400M
Modem Type | Data (Asynchronous/Synchronous)/Fax |
Maximum Data Rate | 14.4K bps |
Maximum Fax Rate | 14.4K bps |
Data Bus | 8-bit ISA |
Fax Class | Class II |
Data Modulation Protocols | Bell 103 & 212A ITU-T V32 & V32 bis & V.22 & V.22bis & V.21 |
Fax Modulation Protocol | ITU-T V.29 & V.27 GRP III |
Error Correction/Compression | ITU-T V.42, & V.42bis,MNP 2-5 |
CONNECTIONS | |||
Purpose | Location | Purpose | Location |
Line out | CN1 | Line in | CN2 |
COM PORT & IRQ SETTINGS | ||||
COM | SW1/1 | SW1/2 | SW1/3 | SW1/4 |
í COM2/IRQ3 | Off | On | Off | On |
COM1/IRQ4 | On | On | On | Off |
COM3/IRQ4 | On | Off | On | Off |
COM4/IRQ3 | Off | Off | Off | On |
INTERRUPT SELECT | |
Setting | P3 |
í IRQ Set by SW1 switches | All open |
IRQ2 | Pins 2 & 3 closed |
IRQ5 | Pins 1 & 2 closed |
PROPRIETARY RESULT CODES | ||
Result code | Message | Description |
9 | CONNECT 600 | Connect at 600bps |
12 | CONNECT 9600 | Connect at 9600bps |
13 | CONNECT 7200 | Connect at 7200bps |
15 | CONNECT 14,400 | Connect at 14,400bps |
16 | CONNECT 19,200 | Connect at 19,200bps |
17 | CONNECT 38,400 | Connect at 38,400bps |
19 | CONNECT 115,200 | Connect at 115,200bps |
51 | CARRIER 12,200 | Carrier at 12,200bps |
i3 - PROPRIETARY PROTOCOLS | |
Type: | CONFIGURATION |
Format: | ATI3 |
Example: | AT I3<CR> |
Description: | Retrieves the software version data. |
W - PROPRIETARY PROTOCOLS | |
Type: | |
Format: | AT [cmds] |
Example: | AT <CR> |
Description: |
W - PROPRIETARY PROTOCOLS | |
Note: | INFORMATIONAL |
Command | Protocol |
í W0 | Protocol negotiation status not reported. |
W1 | Protocol negotiation status reported. |
W2 | Protocol negotiation status not reported; response is DCE |
&M - PROPRIETARY PROTOCOLS | |
Type: | ASYNCHRONOUS MODE |
Format: | AT &M0 |
Example: | AT &M0<CR> |
Description: | Set mode to Asynchronous, identical to &Q0. |
&Q - PROPRIETARY PROTOCOLS | |
Note: | INFORMATIONAL |
Command | Protocol |
í &Q1 | Reserved. |
&Q2 | Reserved. |
&Q3 | Reserved. |
&Q4 | Forces modem to issue OK result code; no changes to operation. |
&Q7 | Reserved. |
&T2 - PROPRIETARY PROTOCOLS | |
Type: | LOOPBACK TEST |
Format: | AT &T2 |
Example: | AT &T2<CR> |
Description: | Reserved. |
\A - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \A0 | Sets MNP block size to 64 char. |
\A1 | Sets MNP block size to 128 char. |
\A2 | Sets MNP block size to 192 char. |
\A3 | Sets MNP block size to 256 char. |
\Bn - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \Bn | Sends n * 100 ms break to the remote, def 300 |
\G - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \G0 | Disables XON/XOFF flow control. |
\G1 | Enables XON/XOFF flow control. |
\K - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \K0 | Break from port; sets to Command mode; no break sent to remote modem. Breaks from command mode; Clears buffers, sends break. Breaks from remote; clears buffers; sends break. |
\K1 | Breaks from port; clears buffers, sends break. Breaks command; clear buffers; sends break. Break from remote; clears buffers passes break on to port. |
\K2 | Breaks from port; sets to command mode; no break sent. |
\k3 | Breaks from port; sends break. Breaks command; sends break. breaks remote and passes break on to port. |
\K4 | Breaks from port; Sets to command mode; no break sent. Breaks command; sends break with sequence of data. Breaks remote; passes break on to port. |
\K5 | Breaks from port; Sends break with sequence of data. Breaks command; sends break with sequence of data. Breaks from remote; passes break on to port. |
\l - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \l0 | Sets stream MNP mode. |
\l1 | Sets block MNP mode. |
\N - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \N0 | Sets mode normal. |
\N1 | Sets mode direct. |
\N2 | Sets mode reliable. |
\N3 | Sets mode auto reliable. |
\O - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \0 | Tries to negotiate a reliable connection. Will only be successful if connection exists. Note: has to be last command in the line. |
\Tn - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \Tn | Programs inactivity timer; n= 0 to 42, def 0. |
\U - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \U | 12 second wait for request from remote to negotiate link. Will only be successful if connection exists. Note: has to be last command in the line. |
\Y - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \Y | Transmits link request (originate mode)/ accepts request (answer mode). Will only be successful if connection exists. Note: has to be last command in the line. |
\Z - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í \Z | Changes from reliable mode to normal mode & clears buffers. |
%C - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %C0 | Disables data compression (MNP) |
%C1 | Enables data compression (MNP) |
%Dn - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %D2 | Sets dictionary size to 2048 (BLTZ.) |
%D0 | Sets dictionary size to 512 (BLTZ). |
%D1 | Sets dictionary size to 1024 (BLTZ). |
%D3 | Sets dictionary size to 4096 single direction 2048 bi-directional (BLTZ). |
%En - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %E0 | Disable auto retrain. |
%E1 | Enable auto retrain. |
%L - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %L | Echoes the received signal (Same strength) range -9dBm to -43dBm. |
%Mn - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %M0 | Disables BLTZ compression mode. |
%M1 | Enables BLTZ transmit only compression mode. |
%M2 | Enables BLTZ receive only compression mode. |
%M3 | Enables BLTZ bi-directional compression mode. |
%P - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %P | Resets BLTZ dictionary (local) and transmits command to reset remote. |
%Q - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %Q | Returns the value of the EQM high order byte. |
%Sn - PROPRIETARY PROTOCOLS | |
Note: | ERROR CORRECTION & DATA COMPRESSION |
Command | Protocol |
í %Sn | Sets BLTZ max number of characters compressed into single BLTZ word. Range 2 to 250, def 32 |
PROPRIETARY COMMAND SET | |||
Type: | Configuration | ||
Format: | ATS(register)=(Command Value) | ||
Example: | ATS36=5 | ||
Description: | Writes to or reads from a specified register. | ||
Register | Command Value | Function | |
S36 | 3 | Negotiation failure - direct connect. | |
S36 | 4 | Negotiation failure - normal connect. | |
S36 | 5 | MNP attempt - direct connect if failure. | |
S36 | 7 | MNP attempt - normal connect if failure. |
PROPRIETARY COMMAND SET | |||
Type: | Configuration | ||
Format: | ATS(register)=(Command Value) | ||
Example: | ATS37=10 | ||
Description: | Writes to or reads from a specified register. | ||
Register | Command Value | Function | |
S37 | 10 | Attempt to negotiate line speed 12,200 | |
S37 | 12 | Attempt to negotiate line speed 7200 |
PROPRIETARY COMMAND SET | |||
Type: | Configuration | ||
Format: | ATS(register)=(Command Value) | ||
Example: | ATS46=138 | ||
Description: | Writes to or reads from a specified register. | ||
Register | Command Value | Function | |
S46 | 138 | Enable error compression & compression. | |
S46 | 136 | Enable error compression & no compression |
PROPRIETARY COMMAND SET | |||
Type: | Configuration | ||
Format: | ATS(register)=(Command Value) | ||
Example: | ATS82=128 | ||
Description: | Writes to or reads from a specified register. | ||
Register | Command Value | Function | |
S82 | 128 | Transmit break in data sequence. | |
S82 | 3 | Transmit break immediately; save data integrity. | |
S82 | 7 | Transmit break immediately; data integrity lost. |