SMART ONE 2834F, SMART ONE 2834V, SMART ONE 2834VP modem/telephone/ISDN Settings and Configuration
BEST DATA PRODUCTS, INC.
SMART ONE 2834F, SMART ONE 2834V, SMART ONE 2834VP
Card Type | Modem (asynchronous) |
Chipset | Unidentified |
I/O Options | Voice (except on Smart One 2834F) |
Maximum Data Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | 8-bit ISA |
Fax Class | Class I & II |
Data Modulation | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation | ITU-T V.17, V.21CH2, V.27ter, V.29 |
Error Correction/Compression | MNP5, MNP10EC, V.42, V.42bis |
CONNECTIONS | |||
Function | Label | Function | Label |
Line out | CN1 | Line in | CN2 |
INTERRUPT SELECTION | ||||
Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 |
í IRQ3 | On | Off | Off | Off |
IRQ4 | Off | On | Off | Off |
IRQ5 | Off | Off | On | Off |
IRQ7 | Off | Off | Off | On |
SERIAL PORT ADDRESS SELECTION | ||
Setting | SW1/5 | SW1/6 |
3F8h (COM1:) | On | On |
í 2F8h (COM2:) | On | Off |
3E8h (COM3:) | Off | On |
2E8h (COM4:) | Off | Off |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
Extended AT Commands |
\A, \B, \G, \K, \N |
%C, %E, %L, %Q |
Special AT Commands |
#CID, +MS |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, S26 |
S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 |
Note: See MHI documentation for complete information. |
UNIDENTIFIED COMMANDS | |
Command | Default |
S37 | 0 |
S201 | Unidentified |
Proprietary AT Command Set
DISPLAY INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays information requested about the modem. |
Command | Function |
I0 | Displays product identification code. |
I1 | Displays ROM checksum. |
I3 | Displays firmware model, revision, and interface. |
I5 | Displays country code. |
I6 | Displays data pump model and revision. |
I7 | Displays the DAA code. |
MNP10 POWER LEVEL ADJUSTMENT | |
Type: | Configuration |
Format: | AT [cmds] )Mn [cmds] |
Description: | Controls automatic transmit power level adjustment during MNP 10 link negotiation. |
Command | Function |
)M0 | Power level adjustment disabled. |
)M1 | Power level adjustment enabled. |
)M2 | Power level adjustment enabled; S40 bit 2 and S201 bit 6 are reset to their default settings. |
MNP10EC MODE | ||
Type: | Configuration | |
Format: | AT [cmds] -SEC=n [cmds] | |
Description: | Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence. | |
Command | Function | |
-SEC=0 | MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line. | |
í -SEC=1 | MNP10EC handshaking enabled. | |
My Books
