APACHE V34I-M modem/telephone/ISDN Settings and Configuration
APACHE MICRO PERIPHERALS, INC.
APACHE V34I-M
Card Type | Modem (asynchronous) |
Chip Set | Rockwell ACi |
I/O Options | None |
Maximum Data Rate | 28.8Kbps |
Maximum Fax Rate | 14.4Kbps |
Data Bus | Unidentified |
Fax Class | Unidentified |
Data Modulation Protocol | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC |
Fax Modulation Protocol | Unidentified |
Error Correction/Compression | MNP5, V.42, V.42bis |
APACHE-MICRO-PERIPHERALS-INC-Modem-asynchronous-AP-98
USER CONFIGURABLE SETTINGS | ||
Setting | Label | Position |
í Factory configured - do not alter | SW1/7 | Unidentified |
í Factory configured - do not alter | SW1/8 | N/A |
Note: SW1/8 may not be present on all models. | ||
INTERRUPT SELECTION | ||||
Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 |
í IRQ3 | Off | Off | Off | On |
IRQ4 | Off | Off | On | Off |
IRQ5 | Off | On | Off | Off |
IRQ7 | On | Off | Off | Off |
SERIAL PORT ADDRESS SELECTION | ||
Setting | SW1/5 | SW1/6 |
3F8h (COM1:) | On | On |
2F8h (COM2:) | Off | On |
3E8h (COM3:) | On | Off |
í 2E8h (COM4:) | Off | Off |
MISCELLANEOUS TECHNICAL NOTE |
Diagram not available. |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
+++, ‘comma’, A/ |
A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z |
Extended AT Commands |
\A, \B, \K, \N |
%C, %E, %L, %Q |
Special AT Commands |
#CID, +MS |
S-Registers |
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 |
S27, S29, S30, S31, S32, S33, S36, S38, S46, S48, S82, S86, S95 |
Note: See MHI documentation for complete information. Registers S39, S40, and S41 are unidentified bit-mapped registers. |
Proprietary AT Command Set
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#>;[cmds] |
Description: | Dials the telephone number indicated according to any modifiers included in the string. |
Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command | Function |
DL | Re-dial last number. |
DP | Pulse dialing enabled. |
DS=n | Dial stored telephone number n. |
DT | Tone dialing enabled. |
DW | Dialing resumed following dial tone detection. |
D, | Dialing paused for amount of time specified in S8 register. |
D! | Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ | Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D$ | Wait for prompt tone detection function enabled. Waits for prompt tone for amount of time specified by the S7 command. |
D^ | Enables calling tone for this call. |
D; | Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
LINE SPEED | |
Type: | Register |
Format | AT [cmds] S37=n [cmds] |
Description: | Sets the maximum allowable data exchange rate attempted during handshake process. |
Command | Function |
í S37=0 | Speed of last connection. |
S37=1 | Maximum speed set to 300bps. |
S37=2 | Maximum speed set to 300bps. |
S37=3 | Maximum speed set to 300bps. |
S37=5 | Maximum speed set to 1200bps. |
S37=6 | Maximum speed set to 2400bps. |
S37=7 | Maximum speed set to 1200/75bps. |
S37=8 | Maximum speed set to 4800bps. |
S37=9 | Maximum speed set to 9600bps. |
S37=10 | Maximum speed set to 12Kbps. |
S37=11 | Maximum speed set to 14.4Kbps. |
S37=12 | Maximum speed set to 7200bps. |
REPORT INFORMATION | |
Type: | Immediate |
Format: | AT [cmds] In [cmds] |
Description: | Displays requested information about the modem. |
Command | Function |
I0 | Reports product identification code. |
I1 | Reports ROM checksum. |
I2 | Tests and reports ROM checksum. |
I3 | Reports modem firmware version and interface type. |
I6 | Reports data pump model and revision. |
My Books
