PCMCIA 14400BPS DATA/14400BPS FAX modem/telephone/ISDN Settings and Configuration

Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘Comma’, A/

A, B, C, D, E, F, H, L, M, O, P, Q, S, T, V, W, X, Y, Z

&C, &D, &E, &G, &J, &L, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \K, \N \Q, \V, \X, \Z, %A, %E

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S11, S12, S16, S18, S25, S26, S36

S38, S39, S46, S48

Note: See MHI Help file for full command documentation.

BIT MAPPED REGISTERS
Register	Default
S14	Read-only
S19	26
S20	32
S21	Read-only
S22	Read-only
S23	Read-only
S27	Read-only

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	Data compression enabled; V.42bis during LAPM, MNP5 during MNP

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Direct mode enabled
\N1	Normal mode enabled
\N2	MNP reliable mode enabled
\N3	MNP auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	V.42 auto-reliable mode enabled
\N6	Reliable mode enabled
í \N7	Auto-reliable mode enabled

DISPLAY FIRMWARE VERSION
Type:	Immediate
Format:	AT [cmds] %V [cmds]
Description:	Displays firmware version information

ENQ/ACK
Type:	Configuration
Format:	AT [cmds] \Hn [cmds]
Description:	Controls Hewlett Packard ENQ/ACK protocol
Command		Function
í \H0		Hewlett Packard ENQ/ACK disabled
\H1		Hewlett Packard ENQ/ACK emulating terminal enabled
\H2		Hewlett Packard ENQ/ACK emulating host

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command		Function
&F0		Restore auto-reliable compression/correction default profile
&F1		Restore auto-reliable compression/correction default profile

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

MINIMUM MODEM PORT RATE
Type:	Configuration
Format:	AT [cmds] %Mn [cmds]
Description:	Selects the minimum modem port rate
Command		Function
í %M300		300bps selected
%M1200		1200bps selected
%M2400		2400bps selected
%M4800		4800bps selected
%M7200		7200bps selected
%M9600		9600bps selected
%M12000		12000bps selected
%M14400		14400bps selected

MODEM PORT RATE
Type:	Configuration
Format:	AT [cmds] %Bn [cmds]
Description:	Selects the modem port rate
Command		Function
%B300		300bps selected
%B1200		1200bps selected
%B2400		2400bps selected
%B4800		4800bps selected
%B7200		7200bps selected
%B9600		9600bps selected
%B12000		12000bps selected
í %B14400		14400bps selected

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Reports ‘OK’
I3	Reports a date code