56K X2 DATA/FAX modem/telephone/ISDN Settings and Configuration

ACTIONTEC ELECTRONICS, INC.

56K X2 DATA/FAX

Card Type
Modem (asynchronous)
Chipset
Unidentified
Maximum Data Rate
56Kbps
Maximum Fax Rate
14.4Kbps
Data Modulation
Bell 103A, 212A
ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34
U.S. Robotics x2
Fax Modulation
ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression
MNP5, V.42, V.42bis
Fax Class
Class I
Data Bus
8-bit ISA
Card Size
Full height, half length

CONNECTIONS
Function
Label
Function
Label
Telephone line out
CN1
Telephone line in
CN2

USER CONFIGURABLE SETTINGS
Setting
Label
Position
í Plug-N-Play enabled
J3/C
Open
Plug-N-Play disabled
J3/C
Closed

SERIAL PORT ADDRESS SELECTION
Setting
J3/A
J3/B
3F8h (COM1:)
Closed
Closed
2E8h (COM2:)
Open
Closed
3F8h (COM3:)
Closed
Open
2E8h (COM4:)
Open
Open
í Plug-N-Play
Open
Open

INTERRUPT SELECTION
Setting
J2/A
J2/B
J2/C
J2/D
J2/E
2
Closed
Open
Open
Open
Open
3
Open
Closed
Open
Open
Open
4
Open
Open
Closed
Open
Open
5
Open
Open
Open
Closed
Open
7
Open
Open
Open
Open
Closed
í Plug-N-Play
Open
Open
Open
Open
Open

SUPPORTED STANDARD COMMANDS
Basic AT Commands
+++, ‘comma’, A/
A, B, D, E, F, H, L, M, O, Q, V, X, Y, Z
&C, &D, &F, &G, &P, &R, &S, &T, &W, &Z
S-Registers
The S-registers are unidentified.
Note: See MHI help file for complete information.

BREAK TYPE
Type:
Configuration
Format:
AT [cmds] &Yn [cmds]
Description:
Configures action of break signal.
Command
Function
&Y0
Break empties buffer.
í &Y1
Break empties buffer and is sent immediately.
&Y2
Break does not empty buffer and is sent immediately.

COMPRESSION MODE
Type:
Configuration
Format:
AT [cmds] &Kn [cmds]
Description:
Selects the type of data compression that will be used.
Command
Function
&K0
Data compression disabled.
í &K1
Auto-detect compression mode.
&K2
Data compression enabled.
&K3
MNP5 data compression only enabled.

CONNECTION SPEED LOWER LIMIT
Type:
Configuration
Format:
AT [cmds] &Un [cmds]
Description:
Sets slowest allowed connection speed if &N is set to 1 or higher.
Command
Function
í &U0
No minimum connect speed.
&U1
Set minimum connect speed to 300bps.
&U2
Set minimum connect speed to 1200bps.
&U3
Set minimum connect speed to 2400bps.
&U4
Set minimum connect speed to 4800bps.
&U5
Set minimum connect speed to 7200bps.
&U6
Set minimum connect speed to 9600bps.
&U7
Set minimum connect speed to 12Kbps.
&U8
Set minimum connect speed to 14.4Kbps.
&U9
Set minimum connect speed to 16.8Kbps.
&U10
Set minimum connect speed to 19.2Kbps.
&U11
Set minimum connect speed to 21.6Kbps.
&U12
Set minimum connect speed to 24Kbps.
&U13
Set minimum connect speed to 26.4Kbps.
&U14
Set minimum connect speed to 28.8Kbps.
&U15
Set minimum connect speed to 31.2Kbps.
&U16
Set minimum connect speed to 33.6Kbps.
&U17
Set minimum connect speed to 33.3Kbps.
&U18
Set minimum connect speed to 37.3Kbps.
&U19
Set minimum connect speed to 41.3Kbps.
&U20
Set minimum connect speed to 42.6Kbps.
&U21
Set minimum connect speed to 44Kbps.
&U22
Set minimum connect speed to 45.3Kbps.
&U23
Set minimum connect speed to 46.6Kbps.
&U24
Set minimum connect speed to 48Kbps.
&U25
Set minimum connect speed to 49.3Kbps.
&U26
Set minimum connect speed to 50.6Kbps.
&U27
Set minimum connect speed to 52Kbps.
&U28
Set minimum connect speed to 53.3Kbps.
&U29
Set minimum connect speed to 54.6Kbps.
&U30
Set minimum connect speed to 56Kbps.
&U31
Set minimum connect speed to 57.3Kbps.

CONNECTION SPEED UPPER LIMIT
Type:
Configuration
Format:
AT [cmds] &Nn [cmds]
Description:
Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed.
Command
Function
í &N0
No maximum connect speed.
&N1
Set maximum connect speed to 300bps.
&N2
Set maximum connect speed to 1200bps.
&N3
Set maximum connect speed to 2400bps.
&N4
Set maximum connect speed to 4800bps.
&N5
Set maximum connect speed to 7200bps.
&N6
Set maximum connect speed to 9600bps.
&N7
Set maximum connect speed to 12Kbps.
&N8
Set maximum connect speed to 14.4Kbps.
&N9
Set maximum connect speed to 16.8Kbps.
&N10
Set maximum connect speed to 19.2Kbps.
&N11
Set maximum connect speed to 21.6Kbps.
&N12
Set maximum connect speed to 24Kbps.
&N13
Set maximum connect speed to 26.4Kbps.
&N14
Set maximum connect speed to 28.8Kbps.
&N15
Set maximum connect speed to 31.2Kbps.
&N16
Set maximum connect speed to 33.6Kbps.
&N17
Set maximum connect speed to 33.3Kbps.
&N18
Set maximum connect speed to 37.3Kbps.
&N19
Set maximum connect speed to 41.3Kbps.
&N20
Set maximum connect speed to 42.6Kbps.
&N21
Set maximum connect speed to 44Kbps.
&N22
Set maximum connect speed to 45.3Kbps.
&N23
Set maximum connect speed to 46.6Kbps.
&N24
Set maximum connect speed to 48Kbps.
&N25
Set maximum connect speed to 49.3Kbps.
&N26
Set maximum connect speed to 50.6Kbps.
&N27
Set maximum connect speed to 52Kbps.
&N28
Set maximum connect speed to 53.3Kbps.
&N29
Set maximum connect speed to 54.6Kbps.
&N30
Set maximum connect speed to 56Kbps.
&N31
Set maximum connect speed to 57.3Kbps.

DISPLAY INFORMATION
Type:
Immediate
Format:
AT [cmds] In [cmds]
Description:
Displays modem properties.
Command
Function
I0
Displays product identification code.
I1
Tests and displays ROM checksum result.
I2
Tests and displays RAM checksum result.
I3
Displays product identification.
I4
Displays current command settings.
I5
Displays current NVRAM settings.
I6
Displays current connection’s statistics.
I7
Displays product configuration.

ERROR CORRECTION MODE
Type:
Configuration
Format:
AT [cmds] &Mn [cmds]
Description:
Selects active error correction protocols.
Command
Function
&M0
Normal mode only.
í &M4
Auto-detect mode.
&M5
Error correction mode only.

EXTENDED RESULT CODES
Type:
Configuration
Format:
AT [cmds] &An [cmds]
Description:
Selects extended result codes.
Command
Function
&A0
Extended result codes disabled.
&A1
Error correction result codes enabled.
&A2
V.32 result code enabled.
í &A3
Error correction and compression result codes enabled.

FLOW CONTROL - MODEM-TO-MODEM
Type:
Configuration
Format:
AT [cmds] &In [cmds]
Description:
Selects the type of modem-to-modem flow control used.
Command
Function
í &I0
Software flow control disabled.
&I1
XON/XOFF pass-through enabled.
&I2
XON/XOFF pass-through disabled.

FLOW CONTROL TYPE
Type:
Configuration
Format:
AT [cmds] &Hn [cmds]
Description:
Sets type of flow control used by modem.
Command
Function
&H0
Flow control disabled.
í &H1
CTS/RTS flow control enabled.
&H2
XON/XOFF flow control enabled.
&H3
CTS/RTS and XON/XOFF flow control enabled.

LOCK SERIAL PORT
Type:
Configuration
Format:
AT [cmds] &Bn [cmds]
Description:
Sets operation of serial port speed.
Command
Function
&B0
Serial speed follows connect speed.
í &B1
Serial speed locked.
&B2
Serial speed locked in error correction mode only.

Headaches Begone! A Systemic Approach To Healing Your Headaches

Don't Let Your Bike Seat Ruin Your Sex Life Book

56K X2 DATA/FAX modem/telephone/ISDN Settings and Configuration

Search

My Books

Discover

Card Type	Modem (asynchronous)
Chipset	Unidentified
Maximum Data Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation	Bell 103A, 212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 U.S. Robotics x2
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42, V.42bis
Fax Class	Class I
Data Bus	8-bit ISA
Card Size	Full height, half length

CONNECTIONS
Function	Label	Function	Label
Telephone line out	CN1	Telephone line in	CN2

USER CONFIGURABLE SETTINGS
Setting	Label	Position
í Plug-N-Play enabled	J3/C	Open
Plug-N-Play disabled	J3/C	Closed

SERIAL PORT ADDRESS SELECTION
Setting	J3/A	J3/B
3F8h (COM1:)	Closed	Closed
2E8h (COM2:)	Open	Closed
3F8h (COM3:)	Closed	Open
2E8h (COM4:)	Open	Open
í Plug-N-Play	Open	Open

INTERRUPT SELECTION
Setting	J2/A	J2/B	J2/C	J2/D	J2/E
2	Closed	Open	Open	Open	Open
3	Open	Closed	Open	Open	Open
4	Open	Open	Closed	Open	Open
5	Open	Open	Open	Closed	Open
7	Open	Open	Open	Open	Closed
í Plug-N-Play	Open	Open	Open	Open	Open

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] &Yn [cmds]
Description:	Configures action of break signal.
Command	Function
&Y0	Break empties buffer.
í &Y1	Break empties buffer and is sent immediately.
&Y2	Break does not empty buffer and is sent immediately.

COMPRESSION MODE
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Selects the type of data compression that will be used.
Command	Function
&K0	Data compression disabled.
í &K1	Auto-detect compression mode.
&K2	Data compression enabled.
&K3	MNP5 data compression only enabled.

CONNECTION SPEED LOWER LIMIT
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Sets slowest allowed connection speed if &N is set to 1 or higher.
Command	Function
í &U0	No minimum connect speed.
&U1	Set minimum connect speed to 300bps.
&U2	Set minimum connect speed to 1200bps.
&U3	Set minimum connect speed to 2400bps.
&U4	Set minimum connect speed to 4800bps.
&U5	Set minimum connect speed to 7200bps.
&U6	Set minimum connect speed to 9600bps.
&U7	Set minimum connect speed to 12Kbps.
&U8	Set minimum connect speed to 14.4Kbps.
&U9	Set minimum connect speed to 16.8Kbps.
&U10	Set minimum connect speed to 19.2Kbps.
&U11	Set minimum connect speed to 21.6Kbps.
&U12	Set minimum connect speed to 24Kbps.
&U13	Set minimum connect speed to 26.4Kbps.
&U14	Set minimum connect speed to 28.8Kbps.
&U15	Set minimum connect speed to 31.2Kbps.
&U16	Set minimum connect speed to 33.6Kbps.
&U17	Set minimum connect speed to 33.3Kbps.
&U18	Set minimum connect speed to 37.3Kbps.
&U19	Set minimum connect speed to 41.3Kbps.
&U20	Set minimum connect speed to 42.6Kbps.
&U21	Set minimum connect speed to 44Kbps.
&U22	Set minimum connect speed to 45.3Kbps.
&U23	Set minimum connect speed to 46.6Kbps.
&U24	Set minimum connect speed to 48Kbps.
&U25	Set minimum connect speed to 49.3Kbps.
&U26	Set minimum connect speed to 50.6Kbps.
&U27	Set minimum connect speed to 52Kbps.
&U28	Set minimum connect speed to 53.3Kbps.
&U29	Set minimum connect speed to 54.6Kbps.
&U30	Set minimum connect speed to 56Kbps.
&U31	Set minimum connect speed to 57.3Kbps.

CONNECTION SPEED UPPER LIMIT
Type:	Configuration
Format:	AT [cmds] &Nn [cmds]
Description:	Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed.
Command	Function
í &N0	No maximum connect speed.
&N1	Set maximum connect speed to 300bps.
&N2	Set maximum connect speed to 1200bps.
&N3	Set maximum connect speed to 2400bps.
&N4	Set maximum connect speed to 4800bps.
&N5	Set maximum connect speed to 7200bps.
&N6	Set maximum connect speed to 9600bps.
&N7	Set maximum connect speed to 12Kbps.
&N8	Set maximum connect speed to 14.4Kbps.
&N9	Set maximum connect speed to 16.8Kbps.
&N10	Set maximum connect speed to 19.2Kbps.
&N11	Set maximum connect speed to 21.6Kbps.
&N12	Set maximum connect speed to 24Kbps.
&N13	Set maximum connect speed to 26.4Kbps.
&N14	Set maximum connect speed to 28.8Kbps.
&N15	Set maximum connect speed to 31.2Kbps.
&N16	Set maximum connect speed to 33.6Kbps.
&N17	Set maximum connect speed to 33.3Kbps.
&N18	Set maximum connect speed to 37.3Kbps.
&N19	Set maximum connect speed to 41.3Kbps.
&N20	Set maximum connect speed to 42.6Kbps.
&N21	Set maximum connect speed to 44Kbps.
&N22	Set maximum connect speed to 45.3Kbps.
&N23	Set maximum connect speed to 46.6Kbps.
&N24	Set maximum connect speed to 48Kbps.
&N25	Set maximum connect speed to 49.3Kbps.
&N26	Set maximum connect speed to 50.6Kbps.
&N27	Set maximum connect speed to 52Kbps.
&N28	Set maximum connect speed to 53.3Kbps.
&N29	Set maximum connect speed to 54.6Kbps.
&N30	Set maximum connect speed to 56Kbps.
&N31	Set maximum connect speed to 57.3Kbps.

DISPLAY INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays modem properties.
Command	Function
I0	Displays product identification code.
I1	Tests and displays ROM checksum result.
I2	Tests and displays RAM checksum result.
I3	Displays product identification.
I4	Displays current command settings.
I5	Displays current NVRAM settings.
I6	Displays current connection’s statistics.
I7	Displays product configuration.

ERROR CORRECTION MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects active error correction protocols.
Command	Function
&M0	Normal mode only.
í &M4	Auto-detect mode.
&M5	Error correction mode only.

EXTENDED RESULT CODES
Type:	Configuration
Format:	AT [cmds] &An [cmds]
Description:	Selects extended result codes.
Command	Function
&A0	Extended result codes disabled.
&A1	Error correction result codes enabled.
&A2	V.32 result code enabled.
í &A3	Error correction and compression result codes enabled.

FLOW CONTROL - MODEM-TO-MODEM
Type:	Configuration
Format:	AT [cmds] &In [cmds]
Description:	Selects the type of modem-to-modem flow control used.
Command	Function
í &I0	Software flow control disabled.
&I1	XON/XOFF pass-through enabled.
&I2	XON/XOFF pass-through disabled.

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] &Hn [cmds]
Description:	Sets type of flow control used by modem.
Command	Function
&H0	Flow control disabled.
í &H1	CTS/RTS flow control enabled.
&H2	XON/XOFF flow control enabled.
&H3	CTS/RTS and XON/XOFF flow control enabled.

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] &Bn [cmds]
Description:	Sets operation of serial port speed.
Command	Function
&B0	Serial speed follows connect speed.
í &B1	Serial speed locked.
&B2	Serial speed locked in error correction mode only.