SPORTSTER VOICE 28.8 FAXMODEM (INTERNAL) modem/telephone/ISDN Settings and Configuration

Card Type	Modem, Fax
Chip Set	Unidentified
I/O Options	Serial ports (2 RJ-11)
Maximum Modem Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34
Fax Modulation Protocol	Unidentified
Error Correction/Compression	MNP 2-4, MNP5, V.42, V.42bis
Fax Class	Class I & II
Data Bus	8-bit ISA
Card Size	Three-quarter length

CONNECTIONS
Function	Label		Function		Label
RJ-11 connector		CN1		RJ-11 connector		CN2

SERIAL PORT ADDRESS
Setting	JP1
COM1 (3F8h)	Pins 1 & 2, 3 & 4, 5 & 6 closed
í COM2 (2F8h)	Pins 3 & 4, 5 & 6 closed
COM3 (3E8h)	Pins 1 & 2, 5 & 6 closed
COM4 (2E8h)	Pins 5 & 6 closed
Plug & Play enabled	Open

IRQ INTERRUPT
IRQ	JP2
IRQ2	Pins 1 & 2 closed
í IRQ3	Pins 3 & 4 closed
IRQ4	Pins 5 & 6 closed
IRQ5	Pins 7 & 8 closed
IRQ7	Pins 9 & 10 closed
Plug & Play enabled	Open

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘comma’, A/

A, B E, F, H, M, O, P, S, T, V, X

&C, &D, &G, &T, &W, &Z

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S18, S25, S38

Note: See MHI Help File for full command documentation.

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DP	Pulse dialing enabled
DS=n	Dial stored telephone number n
D#, *	Extended touch tone pads
DT	Tone dialing enabled/Pulse dialing disabled
D/	Delays for 125ms before proceeding with dial string
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D$	Displays a list of dial commands
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem model and speed
I1	Reports ROM checksum
I2	Tests and reports RAM checksum
I3	Reports product type
I4	Reports current modem settings
I5	Reports nonvolatile memory (NVRAM) settings
I6	Reports link diagnostics
I7	Reports product confirmation
I9	Reports Plug & Play information
I11	Reports call statistics

SPEAKER VOLUME
Type:	Configuration
Format:	AT [cmds] Ln [cmds]
Description:	Controls speaker volume
Command	Function
L0	Low volume setting
L1	Low volume setting
í L2	Medium volume setting
L3	Highest volume setting

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
í Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Result code sending only in Originate mode
Q3	Result code sending only in Ring mode

LONG SPACE DISCONNECT
Type:	Configuration
Format:	AT [cmds] Yn [cmds]
Description:	Commands the modem to disconnect after a 1.6 second break is detected
Command	Function
í Y0	Default is profile 0 setting
Y1	Default is profile 1 setting
Y2	Generic template (&F0)
Y3	Hardware flow control (&F1)
Y4	Software flow control (&F2)

SOFT RESET
Type:	Immediate
Format:	AT [cmds] Zn [cmds]
Description:	Restores modem profiles previously saved in non-volatile RAM using the &W command.
Command	Function
Z0	Restore setting selected by Y command
Z1	Restore setting 0
Z2	Restore setting 1
Z3	Restore to factory default profile 0 (&F0)
Z4	Restore to factory default profile 1 (&F1)
Z5	Restore to factory default profile 2 (&F2)

AUTO-ANSWER - ORIGINATE/ANSWER
Type:	Configuration
Format:	AT [cmds] &An [cmds]
Description:	Selects originate or answer mode when in Auto-Answer mode
Command	Function
&A0	ARQ result codes disabled
&A1	ARQ result codes enabled
&A2	V-modulation indicator added
&A3	Protocol indicators added

SERIAL PORT RATE
Type:	Configuration
Format:	AT [cmds] &Bn [cmds]
Description:	Selects fixed or variable serial port rate
Command	Function
&B0	Variable , follows connection rate
í &B1	Fixed serial port rate
&B2	Fixed in ARQ mode, variable in non-ARQ mode

FACTORY DEFAULT PROFILE
Type:	Configuration
Format:	AT [cmds] &F [cmds]
Description:	Sets values in active profile to values found in the default profile
Command	Function
&F0	Generic template
&F1	Hardware flow control template
&F2	Software flow control template

TRANSMIT DATA FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &H [cmds]
Description:	Sets transmit data flow control
Command	Function
&H0	Generic template
í &H1	Hardware flow control template
&H2	Software flow control template
&H3	Hardware and software flow control templates

RECEIVE DATA SOFWARE FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &I [cmds]
Description:	Sets transmit data flow control
Command	Function
í &I0	Software flow control
&I1	XON/XOFF signals to your modem and remote system
&I2	XON/XOFF signals to your modem only

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options
Command	Function
&K0	Flow control disabled
í &K1	Auto enable/disable
&K2	XON/XOFF flow control enabled
&K3	MNP5 compression disabled

COMMUNICATIONS MODE
Type:	Configuration
Format:	AT [cmds] &Mn [cmds]
Description:	Selects communications mode
Command	Mode
&M0	Normal mode, error control disabled
&M1	Reserved
&M2	Reserved
&M3	Reserved
í &M4	Normal/ARQ
&M5	ARQ mode

CONNECTION SPEED UPPER LIMIT
Type:	Configuration
Format:	AT [cmds] &Nn [cmds]
Description:	Sets required connection speed if &U is set to 0; otherwise, sets fastest allowed connection speed.
Command	Function
&N0	No maximum connect speed.
&N1	Set maximum connect speed to 300bps.
&N2	Set maximum connect speed to 1200bps.
&N3	Set maximum connect speed to 2400bps.
&N4	Set maximum connect speed to 4800bps.
&N5	Set maximum connect speed to 7200bps.
&N6	Set maximum connect speed to 9600bps.
&N7	Set maximum connect speed to 12Kbps.
&N8	Set maximum connect speed to 14.4Kbps.
&N9	Set maximum connect speed to 16.8Kbps.
&N10	Set maximum connect speed to 19.2Kbps.
&N11	Set maximum connect speed to 21.6Kbps.
&N12	Set maximum connect speed to 24Kbps.
&N13	Set maximum connect speed to 26.4Kbps.
&N14	Set maximum connect speed to 28.8Kbps.
&N15	Set maximum connect speed to 31.2Kbps.
&N16	Set maximum connect speed to 33.6Kbps.

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)

RTS/CTS
Type:	Configuration
Format:	AT [cmds] &Rn [cmds]
Description:	Selects RTS/CTS options
Command	Function
&R0	Reserved
&R1	Modem ignores RTS.
&R2	Received Data on computer only on RTS

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR high only while modem is handshaking or connected

CONNECTION SPEED LOWER LIMIT
Type:	Configuration
Format:	AT [cmds] &Un [cmds]
Description:	Sets slowest allowed connection speed if &N is set to 1 or higher.
Command	Function
í&U0	No minimum connect speed.
&U1	Set minimum connect speed to 300bps.
&U2	Set minimum connect speed to 1200bps.
&U3	Set minimum connect speed to 2400bps.
&U4	Set minimum connect speed to 4800bps.
&U5	Set minimum connect speed to 7200bps.
&U6	Set minimum connect speed to 9600bps.
&U7	Set minimum connect speed to 12Kbps.
&U8	Set minimum connect speed to 14.4Kbps.
&U9	Set minimum connect speed to 16.8Kbps.
&U10	Set minimum connect speed to 19.2Kbps.
&U11	Set minimum connect speed to 21.6Kbps.
&U12	Set minimum connect speed to 24Kbps.
&U13	Set minimum connect speed to 26.4Kbps.
&U14	Set minimum connect speed to 28.8Kbps.
&U15	Set minimum connect speed to 31.2Kbps.
&U16	Set maximum connect speed to 33.6Kbps.

RESTORE PROFILE ON POWER-UP
Type:	Configuration
Format:	AT [cmds] &Yn [cmds]
Description:	Restores a selected profile into the active profile on power-up (hard reset)
Command	Function
&Y0	Destructive, doesn’t send break
&Y1	Destructive, expedited
&Y2	Nondestructive, expedited
&Y3	Reserved

BIT-MAPPED REGISTER S13
Format:		AT [cmds] S13=n [cmds]
Range:		0-174
Unit:		Bit-mapped
Description:		Controls reset, dial mode
Bit	Value	Function
0	0 1	Unidentified Resets when DTR drops
1	0 í 1	Unidentified Resets non-MNP transmit buffer from 1.5K to 128bytes
2	0 1	Unidentified Sets backspace key to delete
3	0 1	Unidentified On DTR signal, auto dials number stared at NVRAM position 0
4	0 1	Unidentified At power on/reset, auto dials number stared at NVRAM position 0
5	0	Reserved
6	0	Reserved
7	0 1	Unidentified Disconnect on escape code

BIT-MAPPED REGISTER S15
Format:		AT [cmds] S15=n [cmds]
Unit:		Bit-mapped
Description:		Disable/Enable MNP
Bit	Value	Function
0	0 1	Enable ARQ/MNP for V.22 Disable ARQ/MNP for V.22
1	0 1	Enable ARQ/MNP for V.22bis Disable ARQ/MNP for V.22bis
2	0 1	Enable ARQ/MNP for V.32/V.32bis/V.32terbo Enable ARQ/MNP for V.32/V.32bis/V.32terbo
3	0 1	Enable MNP handshake Disable MNP handshake
4	0 1	Enable MNP level 4 Disable MNP level 4
5	0 1	Enable MNP level 3 Disable MNP level 3
6	0 1	MNP compatibility MNP incompatibility
7	0 1	Enable V.42 operation Disable V.42 operation

TEST MODES
Type:		Register
Format:		AT [cmds] S16=n [cmds]
Unit:		Bit-mapped
Description:		Controls touch tone dialing test.
Bit	Value	Function
0	0	Reserved
1	0 1	Touch tone dialing test not in progress Touch tone dialing test in progress
2-7	0	Reserved

INACTIVITY TIMER
Type:	Register
Format	AT [cmds] S19=n [cmds]
Range:	0-255
Unit:	1 minute
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.
Note: S19=0 disables the timer and allows indefinite inactivity.

BREAK LENGTH
Type:	Register
Format	AT [cmds] S21=n [cmds]
Unit:	10ms
Description:	Sets duration of breaks sent from the modem to the computer
Note: Applies to MNP or V.42 mode only.

FLOW CONTROL CHARACTER - XON
Type:	Register
Format:	AT [cmds] S22=n [cmds]
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XON

FLOW CONTROL CHARACTER - XOFF
Type:	Register
Format:	AT [cmds] S23=n [cmds]
Range:	0-255
Unit:	ASCII
Description:	Sets the character used to represent XOFF

BIT-MAPPED REGISTER S27
Format		AT [cmds] S27=n [cmds]
Range:		0-255
Unit:		Bit-mapped
Description:		Enables/disables modulation protocols
Bit	Value	Function
0	0 1	Disable ITU-T modulation at 300bps for overseas calls: in V.21 mode, the modem answers both overseas and domestic calls, but only originates V.21 calls Enable ITU-T modulation at 300bps for overseas calls: in V.21 mode, the modem answers both overseas and domestic calls, but only originates V.21 calls
1	0 1	Disable unencoded modulation in V.32 mode Enable unencoded modulation in V.32 mode
2	0 1	Enable V.32 modulation Disable V.32 modulation
3	0 1	Enable 2100Hz answer tone Disable 2100Hz answer tone
4	0 1	Disable V.23 fallback mode Enable V.23 fallback mode
5	0 1	Enable V.32bis mode Disable V.32bis mode
6	0 1	Enable V.42 selective reject Disable V.42 selective reject
7	0 1	Enable codes Disable codes and displays 900 code instead

CONNECTION TIME
Type:	Register
Format	AT [cmds] S28=n [cmds]
Range:	0-255
Unit:	.01 second
Description:	Sets V.32 duration
Command	Function
S28=0	Eliminates the V.32 answer tone for a faster connection
S28=8	Times are in .1 second
S328=255	Disable connections except V.32 at 9600bps

FALLBACK TIMER
Type:	Register
Format	AT [cmds] S29=n [cmds]
Range:	0-255
Unit:	.01 second
Description:	Sets the duration of the V.21 answer mode fallback timer

VOLUME CONTROL
Type:	Register
Format	AT [cmds] S31=n [cmds]
Range:	0-255
Description:	Sets volume control for speakerphone

BIT-MAPPED REGISTER S32
Format:		AT [cmds] S32=n [cmds]
Range:		0-255
Description:		Select setup for 28.8 and higher speed modems
Bit	Value		Function
0	0 1		Disable V.8 call indicate Enable V.8 call indicate
1	0 1		Disable V.8 mode Enable V.8 mode
2	0 1		Enable V.FC modulation Disable V.FC modulation
3	0 1		Enable V.34 modulation Disable V.34 modulation
4	0 1		Enable 33.6kbps modulation Disable 33.6kbps modulation
5-6	0 1		Reserved

BIT-MAPPED REGISTER S33
Format:		AT [cmds] S33=n [cmds]
Range:		0-255
Description:		Disable/enable data rates
Bit	Value		Function
0	0 1		Enable 2400 symbol rate Disable 2400 symbol rate
1	0 1		Enable 2743 symbol rate Disable 2743 symbol rate
2	0		Enable 2800 symbol rate Disable 2800 symbol rate
3	0 1		Enable 3000 symbol rate Disable 3000 symbol rate
4	0 1		Enable 3200 symbol rate Disable 3200 symbol rate
5	0 1		Enable 3429 symbol rate Disable 3429 symbol rate
6	0		Reserved
7	0 1		Enable shaping Disable shaping

BIT-MAPPED REGISTER S34
Format:		AT [cmds] S34=n [cmds]
Range:		0-255
Description:		Disable/enable trellis encoding
Bit	Value		Function
0	0 1		Enable 8S-2D trellis encoding Disable 8S-2D trellis encoding
1	0 1		Enable 16S-4D trellis encoding Disable 16S-4D trellis encoding
2	0 1		Enable 32S-2D trellis encoding Disable 32S-2D trellis encoding
3	0 1		Enable 64S-4D trellis encoding Disable 64S-4D trellis encoding
4	0 1		Enable non-linear coding Disable non-linear coding
5	0 1		Enable TX level deviation Disable TX level deviation
6	0 1		Enable pre-emphasis Disable pre-emphasis
7	0 1		Enable pre-coding Disable pre-coding