SMARTMUX DRI-200 IO card Settings and Configuration
QUATECH, INC.
SMARTMUX DRI-200
Card Type | I/O Card |
Chipset Controller | Unidentified |
I/O Options | Serial I/O |
Maximum Dram | N/A |
CONNECTIONS | |
Purpose | Location |
Digital module connector | J1 |
Analog module header | H1 |
Serial I/O and power (see table below) | SC1 |
SCREW TERMINAL BLOCK CONNECTIONS | ||
Purpose | Name | Location |
RS-482/485 from host, positive | FH+ | SC1/1 |
RS-482/485 from host, negative | FH- | SC1/2 |
RS-422/485 to host, positive | TH+ | SC1/3 |
RS-422/485 to host, negative | TH- | SC1/4 |
RS-422/485 from bus chain, positive | FO+ | SC1/5 |
RS-422/485 from bus chain, negative | FO- | SC1/6 |
RS-422/485 to bus chain, positive | TO+ | SC1/7 |
RS-422/485 to bus chain, negative | TO- | SC1/8 |
5V DC power in | +5V | SC1/9 |
Signal ground | GND | SC1/10 |
Power switch | ALE | SC1/11 |
Reset button | RST | SC1/12 |
EEPROM WRITE ENABLE | |
Setting | SW2/4 |
Disabled | Off |
Enabled | On |
FACTORY CONFIGURED-DO NOT ALTER | |
Switch/Jumper | Setting |
SW1/1 | On |
JP1 | Open |
JP2 | Pins 1 & 2, 3 & 4 closed |
JP3 | Open |
NODE ADDRESS SELECTION | |||||||
Address | SW1/2 | SW1/3 | SW1/4 | SW1/5 | SW1/6 | SW1/7 | SW1/8 |
0 | On | On | On | On | On | On | On |
1 | On | On | On | On | On | On | Off |
2 | On | On | On | On | On | Off | On |
3 | On | On | On | On | On | Off | Off |
124 | Off | Off | Off | Off | Off | On | On |
125 | Off | Off | Off | Off | Off | On | Off |
126 | Off | Off | Off | Off | Off | Off | On |
127 | Off | Off | Off | Off | Off | Off | Off |
Note: A total of 127 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 8=1, 7=2, 6=4, 5=8, 4=16, 3=32, 2=64. Add the values of the off switches to obtain the correct node address. (On=0, Off=1) | |||||||
SERIAL PORT CONFIGURATION | |||
Baud Rate | SW2/1 | SW2/2 | SW2/3 |
300 | On | On | On |
600 | Off | On | Off |
1200 | On | Off | On |
2400 | Off | Off | On |
4800 | On | On | Off |
9600 | Off | On | Off |
19200 | On | Off | Off |
38400 | Off | Off | Off |
BUS TYPE SELECTION | |
Bus Type | SW2/5 |
Multi-Drop | On |
Daisy Chain | Off |
RESISTOR SETUP FOR SERIAL I/O | ||||||
Usage | Bias from Host | Match from Host | Match Out | SW2/6 | SW2/7 | SW2/8 |
End of Multi-Drop Chain Daisy Chain Node | Yes | Yes | Yes | On | On | On |
Multi-Drop Node | No | No | No | Off | Off | Off |
DIAGNOSTIC LEDS | |||
LED | Color | Status | Condition |
LED1 | Green | Flashing | Sending data |
LED2 | Green | Flashing | Receiving data |
LED3 | Red | On | Power on |
LED3 | Red | Flashing | Startup or hardware failure |
LED3 | Red | Off | Power off or hardware failure |
ARI-12G DAUGHTERBOARD
CONNECTIONS | |
Purpose | Location |
Analog module connector | J1 |
Mainboard header | H1 |
Power (see table below) | SC1 |
SCREW TERMINAL BLOCK CONNECTIONS | ||
Purpose | Name | Location |
+12V DC power in | +12V | SC1/1 |
-12V DC power in | -12V | SC1/2 |
Signal ground | GND | SC1/3 |
A/D CONVERTER MODE SELECTION | |
Mode | JP1 |
Bipolar mode | Pins 1 & 2 closed |
Unipolar mode | Pins 2 & 3 closed |
D/A CONVERTER MODE SELECTION | |
Mode | JP2 |
Bipolar mode | Pins 1 & 2, 4 & 5 closed |
Unipolar mode | Pins 2 & 3, 5 & 6 closed |
My Books
