S-1003 (REV. B) IO card Settings and Configuration
GLOBETEK, INC.
S-1003 (REV. B)
Card Type | Serial |
Chipset | Startech ST16C554D |
I/O Options | Serial ports (4) |
Data Bus | 16-bit ISA |
CONNECTIONS | |||
Function | Label | Function | Label |
Serial port 1 via RJ-45 connector | P1 | Serial port 3 via RJ-45 connector | P3 |
Serial port 2 via RJ-45 connector | P2 | Serial port 4 via RJ-45 connector | P4 |
USER CONFIGURABLE SETTINGS | |||
Setting | Label | Position | |
| » | Factory configured - do not alter | S2/4 | Unidentified |
| » | Factory configured - do not alter | S2/5 | Unidentified |
| » | Status register enabled | S2/8 | On |
Status register disabled | S2/8 | Off | |
BASE I/O ADDRESS SELECTION | |||||||
Setting | SW1/1 | SW1/2 | SW1/3 | SW1/4 | SW1/5 | SW1/6 | |
0000h | On | On | On | On | On | On | |
0020h | On | On | On | On | On | On | |
0040h | On | On | On | On | On | On | |
0060h | On | On | On | On | On | On | |
0080h | On | On | On | On | On | On | |
| » | 0320h | On | On | On | On | On | On |
FF60h | Off | Off | Off | Off | Off | Off | |
FF80h | Off | Off | Off | Off | Off | Off | |
FFA0h | Off | Off | Off | Off | Off | Off | |
FFC0h | Off | Off | Off | Off | Off | Off | |
FFE0h | Off | Off | Off | Off | Off | Off | |
BASE I/O ADDRESS SELECTION (CON’T) | ||||||
Setting | SW1/7 | SW1/8 | SW2/1 | SW2/2 | SW2/3 | |
0000h | On | On | On | On | On | |
0020h | On | On | On | On | Off | |
0040h | On | On | On | Off | On | |
0060h | On | On | On | Off | Off | |
0080h | On | On | Off | On | On | |
| » | 0320h | Off | Off | On | On | Off |
FF60h | Off | Off | On | Off | Off | |
FF80h | Off | Off | Off | On | On | |
FFA0h | Off | Off | Off | On | Off | |
FFC0h | Off | Off | Off | Off | On | |
FFE0h | Off | Off | Off | Off | Off | |
Note: A total of 4096 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW1/1 is the Most Significant Bit and switch SW2/3 is the Least Significant Bit. The switches have the following decimal values: SW1/1=32768, SW1/2=16384, SW1/3=8192, SW1/4=4096, SW1/5=2048, SW1/6=1024, SW1/7=512, SW1/8=256, SW2/1=128, SW2/2=64, SW2/3=32. Turn off the switches and add the values of the switches that are off to obtain the correct memory address. (Off=1, On=0) | ||||||
SERIAL PORT CONFIGURATION | |||||
Port 1 | Port 2 | Port 3 | Port 4 | S2/6 | S2/7 |
Enabled | Disabled | Disabled | Disabled | On | On |
Enabled | Enabled | Disabled | Disabled | On | Off |
Enabled | Enabled | Enabled | Disabled | Off | On |
Enabled | Enabled | Enabled | Enabled | Off | Off |
SERIAL PORT INTERRUPT SELECTION | |||||||
Setting | JP1/A | JP1/B | JP1/C | JP1/D | JP1/E | JP1/F | |
IR/FONT> | Open | Open | Open | Open | Open | Open | |
IRQ3 | Open | Open | Open | Open | Open | Open | |
IRQ4 | Open | Open | Open | Open | Open | Open | |
IRQ5 | Open | Open | Open | Open | Open | Open | |
IRQ6 | Open | Open | Open | Open | Open | Open | |
IRQ7 | Open | Open | Open | Open | Open | Open | |
IRQ10 | Open | Open | Open | Open | Open | Closed | |
IRQ11 | Open | Open | Open | Open | Closed | Open | |
IRQ12 | Open | Open | Open | Closed | Open | Open | |
IRQ14 | Open | Open | Closed | Open | Open | Open | |
IRQ15 | Open | Closed | Open | Open | Open | Open | |
| » | Shared | Closed | Open | Open | Open | Open | Open |
Disabled | Open | Open | Open | Open | Open | Open | |
SERIAL PORT INTERRUPT SELECTION (CON’T) | |||||||
Setting | JP1/G | JP1/H | JP1/I | JP1/J | JP1/K | JP1/L | |
IR/FONT> | Open | Open | Open | Open | Open | Closed | |
IRQ3 | Open | Open | Open | Open | Closed | Open | |
IRQ4 | Open | Open | Open | Closed | Open | Open | |
IRQ5 | Open | Open | Closed | Open | Open | Open | |
IRQ6 | Open | Closed | Open | Open | Open | Open | |
IRQ7 | Closed | Open | Open | Open | Open | Open | |
IRQ10 | Open | Open | Open | Open | Open | Open | |
IRQ11 | Open | Open | Open | Open | Open | Open | |
IRQ12 | Open | Open | Open | Open | Open | Open | |
IRQ14 | Open | Open | Open | Open | Open | Open | |
IRQ15 | Open | Open | Open | Open | Open | Open | |
| » | Shared | Open | Open | Open | Open | Open | Open |
Disabled | Open | Open | Open | Open | Open | Open | |
Note:JP1 sets the address for port 1. The settings for JP2 through JP4 are identical and set the addresses for ports 2 through 4, respectively. | |||||||
SHARED INTERRUPT SELECTION | |||||||
Setting | JP5/A | JP5/B | JP5/C | JP5/D | JP5/E | JP5/F | |
IR/FONT> | Open | Open | Open | Open | Open | Open | |
IRQ3 | Open | Open | Open | Open | Open | Open | |
IRQ4 | Open | Open | Open | Open | Open | Open | |
IRQ5 | Open | Open | Open | Open | Open | Open | |
IRQ6 | Open | Open | Open | Open | Open | Open | |
IRQ7 | Open | Open | Open | Open | Open | Open | |
| » | IRQ10 | Open | Open | Open | Open | Open | Closed |
IRQ11 | Open | Open | Open | Open | Closed | Open | |
IRQ12 | Open | Open | Open | Closed | Open | Open | |
IRQ14 | Open | Open | Closed | Open | Open | Open | |
IRQ15 | Open | Closed | Open | Open | Open | Open | |
Disabled | Closed | Open | Open | Open | Open | Open | |
SHARED INTERRUPT SELECTION (CON’T) | |||||||
Setting | JP5/G | JP5/H | JP5/I | JP5/J | JP5/K | JP5/L | |
IR/FONT> | Open | Open | Open | Open | Open | Closed | |
IRQ3 | Open | Open | Open | Open | Closed | Open | |
IRQ4 | Open | Open | Open | Closed | Open | Open | |
IRQ5 | Open | Open | Closed | Open | Open | Open | |
IRQ6 | Open | Closed | Open | Open | Open | Open | |
IRQ7 | Closed | Open | Open | Open | Open | Open | |
| » | IRQ10 | Open | Open | Open | Open | Open | Open |
IRQ11 | Open | Open | Open | Open | Open | Open | |
IRQ12 | Open | Open | Open | Open | Open | Open | |
IRQ14 | Open | Open | Open | Open | Open | Open | |
IRQ15 | Open | Open | Open | Open | Open | Open | |
Disabled | Open | Open | Open | Open | Open | Open | |
SERIAL PORT CLOCK SPEED | ||||
Setting | Multiplier | JP6/A | JP6/B | JP6/C |
1.8342MHz | 1 | Closed | Open | Open |
3.6864MHz | 2 | Open | Closed | Open |
7.3728MHz | 4 | Open | Open | Closed |
My Books
