Hard Drive: TOSHIBA: MK-537FB 1000MB 3.5"/HH SCSI2 SE

M K - 5 3 7 F B    TOSHIBA
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    1979|     |     |
Capacity form/unform  1000/      MB        Heads          13|     |     |
Seek time   / track  12.5/ 2.0 ms          Sector/track     |     |     |
Controller           SCSI2 SINGLE-ENDED    Precompensation
Cache/Buffer           256 KB              Landing Zone
Data transfer rate    1.750 MB/S int       Bytes/Sector      512
                     10.000 MB/S ext SYNC
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 50    |    -10 60
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle          10.0 W     Shock        g        10       |     40
       seek               W     Rotation   RPM      3600
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h     200000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

TOSHIBA MK438FB/MK-53XFB INSTALLATION NOTES P/N 480033-G0

  +---------------------------------------------------------+
  |               +---------1                         RN1+-+|XX
  |               +---------+ J1                         | ||XX
  |                                                      | ||XX
  |                                                      | ||XX
  |                                                      +*+|XX
  +-+                                                 RN2+-+|XX
   ++-+                                                  | ||XX
   |  |J2                                                | ||XX
   |  |HDA                         PCV                   | ||XX
   |  |                            VISIBLE SIDE          +*+|XX J4
   ++-+                                               RN3+-+|XX
  +-+                                                    | ||XX
  |                                                      | ||XX
  |                                                      | ||XX
  |                                                      +*+|  1
  |+-+FACTORY USE!                                          |XX
  |+-+J5                                                    |XX Power
  +---------------------------------------------------------+  1
  ALL DRIVES (EXCEPT MK-438FB, ASSY #0605)

   MK-438FB ASSY #0605
  +---------------------------------------------------------+
  |               +---------1                               |XX
  |               +---------+ J1                            |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  +-+                                                       |XX
   ++-+                                                     |XX
   |  |J2                                                   |XX
   |  |HDA                         PCV                      |XX
   |  |                            VISIBLE SIDE             |XX J4
   ++-+                                                     |XX
  +-+                                                       |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |  1
  |                                                         |XX
  |                                                         |XX Power
  +---------------------------------------------------------+  1

Jumpers

TOSHIBA MK438FB/MK-53XFB INSTALLATION NOTES P/N 480033-G0

Jumper Setting
==============

J1 Option Jumper
----------------
The MK-438FB and MK-53XBF have one jumper block, J1 (use 2mm jumper
part numbers: P/N 037001 [Toshiba] or P/N 86730-001 [Dupont].

       +-------------------------------- MANUFACTURING
       |  +----------------------------- ATTENTION
       |  |  +-------------------------- START COMMAND
       |  |  |  +----------------------- PARITY ENABLE
       |  |  |  |  +-------------------- INDEX IN
       |  |  |  |  |  +----------------- INDEX OUT
       |  |  |  |  |  |  +-------------- TERM POWER
       |  |  |  |  |  |  |  +----------- EXTERNAL LED
       |  |  |  |  |  |  |  |  +-------- SCSI ID 2
       |  |  |  |  |  |  |  |  |  +----- SCSI ID 1
       |  |  |  |  |  |  |  |  |  |  +-- SCSI ID 0
     +2-+4-+6-+8-+10+12+14+16+18+20+22+
     |  |XX|XX|XX|XX|  |XX|  |XX|XX|  |   XX = Shipped with jumper on.
     +1-+3-+5-+7-+9-+11+13+15+17+19+21+

CAUTION
Manufacturing pin location is for factory use only. If jumper is
installed, data will be destroyed on drive.

MANUFACTURING ENABLE (J1-PIN 1&2) - CAUTION FACTORY USE ONLY

UNIT ATTENTION ENABLE (J1-PINS 3&4) - PRESENT WHEN SHIPPED
Removal will inhibit ubit attention at power on or SCSI reset.

START ON COMMAND ENABLE (J1-PINS 5&6) - PRESENT WHEN SHIPPED
When removed the spindle motor will start only on receipt of the
Start Unit command.

SCSI BUS PARITY ENABLE (J1-PINS 7&8) - PRESENT WHEN SHIPPED
When removed, drive will not check for parity.

SPINDLE SYNCHRONIZATION (J1-PINS 9-12) - PINS 11&12 NOT PRESENT WHEN
SHIPPED SPARE JUMPER LOCATED AT PINS 9&10 WHEN SHIPPED
Spindle Synchronization capability accommodated using a 4-pin cable
connector (pins 9 - 12 of jumper block).

TERMINATOR POWER SOURCE (J1-PINS 13&14) - PRESENT WHEN SHIPPED
When removed, drive does not supply terminator power. The SCSI BUS
requires termination to be installed on the last unit located on the
BUS. There are two versions of the PCB. One version use three (3) SIP
Resistors (RN1, RN2 & RN3) to provide BUS termination. The other
version uses a SCSI in-line cable terminator (this terminator is
shipped with the drive in a separate bag).

EXTERNAL LED (J1-PINS 15&16) - NOT PRESENT WHEN SHIPPED
An external LED may be driven by connecting the cathode to pin 16 and
the anode to pin 15 on the jumper block.

SCSI BUS ID (J1 PINS 17-22)
Jumper J1, pins 17-22, are used to select the SCSI ID of the drive.
The drive can be selected to have any ID in the range 0 through 7. No
two devices on the same SCSI bus can have the same ID.

   +----------+-----------------------+
   | SCSI ID  | 17&18   19&20   21&22 |
   |          | ID2   | ID1   | ID0   |
   +----------+-------+-------+-------+
   |    0     | OPEN  | OPEN  | OPEN  |
   |    1     | OPEN  | OPEN  | CLOSED|
   |    2     | OPEN  | CLOSED| OPEN  |
   |    3     | OPEN  | CLOSED| CLOSED|
   |    4     | CLOSED| OPEN  | OPEN  |
   |    5     | CLOSED| OPEN  | CLOSED|
   |    6     | CLOSED| CLOSED| OPEN  |
   |    7     | CLOSED| CLOSED| CLOSED|
   +----------+-------+-------+-------+
   NOTE: Drive is shipped with ID = 6

Install

TOSHIBA MK-438FB/MK-53XFB INSTALLATION NOTES P/N 480033-G0

Notes on Installation
=====================

Mounting
--------
When mounting the drive, adequate clearance should be provided from
the outer surface of the HDA and PCB to allow vibration to be ab-
sorbed by the drive shock mounts and to allow for the passage of
cooling ir over the drive.

 WARNING
 The side mounting screw must not penetrate into the drive frame more
 than 0.10 inches (2.5mm) or damage to the HDA will result. Length of
 screw = Thickness of mounting material + 0.05 - 0.10 inches. Typical
 screw length for most applications is 3/16". (A washer should be used
 to meet non-standard screw length requirements.)

Cooling and disk drive enclosure
--------------------------------
The MK-438FB and MK-53XFB can be mounted vertically or horizontally.
Convection cooling is used. It is recommended that cabinetry design
allow for adequate air flow. The disk enclosure must be designed to
maintain an even temperature within the drive's environmental limits
and throughout the drive's various components.

Terminator Resistors
--------------------
The resistors must be removed on all but the last physical device on
the SCSI BUS.

Optional Hard Disk Drive Kits
-----------------------------
If desired, an optional 3.5" hard drive mounting kit (P/N HDD002KU)
is available for mounting the hard drive in a 5.25" half height
cavity. Also available are PC/AT mounting rails (P/N AT8001T).

The following accesories are available:

 P/N 290000003-A0  SCSI ID cable for remote selection of ID
 P/N CAB-01-24     SCSI 50 Pin Flat Ribbon Cable
 P/N 140-001       External SCSI Bus single-ended terminator
                   (Method Electronics, Inc. P/N SP-550-06-0)
 P/N 270008-A1     LED extension cable assembly

Versions of ONTRACK's DiskManager for DOS, Macintosh operating
systems and DiskManager-N for Novell Network systems can be used with
this drive.

General Description
-------------------
The MK-438FB and MK-53XFB series consist of 3.5-inch hard disk drives
designed primarily for high performance personal computers such as
IBM PC/AT or compatible, Apple Macintosh and Sun Micro Work Stations.

CAUTION
Please use caution when handling and installing drive. Avoid
excessive shock, vibration and static build up in the installation
environment. The MK-438FB and MK-53XFB are precision devices, do not
drop drive onto a surface. Until drive is mounted in your system, its
built in shock absorbers are inactive and even a small drop may
cause permanent damage.

 DC Power and pin connector assignments
 --------------------------------------
 +------------+   pin 1    +12 VDC
 | 1  2  3  4 |   pin 2    +12 Volts Return
 +------------+   pin 3    + 5 Volts Return
                  pin 4    + 5 VDC