M K - 1 3 4 F A ( R L L ) TOSHIBA NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders 733| | | Capacity form/unform 65/ MB Heads 7| | | Seek time / track 25.0/ 7.0 ms Sector/track 26| | | Controller RLL / ST506 Precompensation 512 Cache/Buffer KB Landing Zone Data transfer rate 0.938 MB/S int Bytes/Sector 512 0.938 MB/S ext Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 40 | -40 70 Power: sleep W Humidity % 8 80 | 5 90 standby W Altitude km -0.300 3.000| -0.400 15.000 idle W Shock g 10 | 40 seek W Rotation RPM 3600 read/write W Acoustic dBA 48 spin-up W ECC Bit WITH 11BIT BURST COR MTBF h 30000 Warranty Month Lift/Lock/Park YES Certificates
TOSHIBA MK-130FA PRODUCT SPECIFICATIONS 71Y101562, REV. A
+---------------------------------------------------------+ | Factory |XX | +---+PJ5 |XX | 1---+ |XX J2 | |XXData | | 1 | |XX | 1-+PJ4 |XX | | | |XX J1 | | | |XXControl | | | |XX | | | |XX | | | |XX | +-+ |XX | |XX ++ | 1 ++LED 1XXXXXX Power +---------------------------------------------------------+ J3
TOSHIBA MK130FA PRODUCT SPECIFICATIONS 71Y101562, REV. A
Jumper Setting
==============
PJ4 --- +-2-----------------------------32+ | o o o o o o o o o o o o o o o o | | o o o o o o o o o o o o o o o o | +-1-----------------------------31+
The 32 pin connector for the selectable functions is provided on the
printed circuit board. The specific functions are selected by the
jumper plugs to the pins on this connector.
Pins Definitions Meanings ------------------------------------------------------------------- 01, 02 WRITE PROTECT Write protected when the jumper plug is connected. 03, 04 RADIAL MODE The drive is always selected when the jumper plug is connected. 05, 06 DRIVE NO. 4 UNIT NO. 4 is assigned when the jumper plug is connected. 07, 08 DRIVE NO. 3 UNIT NO. 3 is assigned when the jumper plug is connected. 09, 10 DRIVE NO. 2 UNIT NO. 2 is assigned when the jumper plug is connected. 11, 12 DRIVE NO. 1 UNIT NO. 1 is assigned when the jumper plug is connected.
13, 14 ---+ 15, 16 | 17, 18 +--- TERMINATOR Should be closed on the last drive on the 19, 20 | daisy-chain. 21, 22 | 23, 24 ---+
25, 26 ---+--- FOR ADJUSTMENT USE ONLY 27, 28 ---+
29, 30 ---+--- DRIVE MODEL 31, 32 ---+
Drive ID
--------
Five pairs are assigned to set the drive number. By these pairs, it
is possible to set any drive ID from 1 to 4 or to set radial
connection.
Write protect
-------------
Write protection is activated by the jumper plug to the pair of pins
of the connector.
Terminators
-----------
Terminator resistors are connected to the interface signals when
plugged.
Miscellanious
-------------
Two pairs of pins for the drive model definition and two pairs for
the adjustment are prepaired in the connector. These pairs must not
be changed by the customer.
Indicator LED
-------------
The indicator LED and the connector for additional external
indication are prepared at the front on the printed circuit board.
The signal for indication becomes "ON" when the both UNIT SELECTED
and READY signals are "TRUE".
PJ5 FACTORY RESERVED
--------------------
1-3 MUST OPEN, and 4 must CLOSED