lotus

previous page: Hard Drive: SEAGATE: ST352X 42MB 3.5"/SL    IDE / XT
  
page up: Hard Drive Specs from SEAGATE
  
next page: Hard Drive: SEAGATE: ST3543A      FILEPRO 541MB 3.5"/SL    ATA2 FAST

Hard Drive: SEAGATE: ST3541A CABO 540MB 3.5"/SL ATA2 FAST




S T 3 5 4 1 A                   C A B O    SEAGATE
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders        | 1048|  524| 1024
Capacity form/unform   540/      MB        Heads           2|   16|   32|   16
Seek time   / track  14.0/ 3.0 ms          Sector/track     |   63|   63|   63
Controller           IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer            64 KB              Landing Zone
Data transfer rate          MB/S int       Bytes/Sector      512
                     16.600 MB/S ext
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep          1.0 W     Humidity     %         8 80    |      8 80
       standby            W     Altitude    km    -0.061  3.048| -0.061 12.192
       idle           3.8 W     Shock        g         5       |     75
       seek           5.7 W     Rotation   RPM      3600
       read/write     4.9 W     Acoustic   dBA        34
       spin-up            W     ECC        Bit
                                MTBF         h     300000
                                Warranty Month        36
Lift/Lock/Park     YES          Certificates

Jumpers

SEAGATE ST3541A STINGRAY QUICK REFERENCE GUIDE

Jumper Setting
==============

C/D Master/Slave Configuration
------------------------------
CLOSED Single Drive
CLOSED Master Drive
OPEN Slave Drive

CS Cable Select
---------------
OPEN Cable select option disabled
CLOSED Cable select option enabled

NOTE
When using the CS option, the C/D jumper must be open.

 Front View                      +----  NOT USED
                                 | +--  Master ON, Slave OFF (C/D)
                                 | |
     (TOP)         o o o o o   o o o1
 Option Block   ---  o o o o---o o o2------------------
    (BOTTOM)       +---+---+   |
                       |       |
           RESERVED ---+       |
           Cable Select  ------+

The C/D jumper is used to determine whether the drive is a master
(drive C) or a slave (drive D). The drive is configured as a master,
when jumpered, and a slave when not jumpered.

When using CS option, the C/D jumper MUST be open

Master/Slave Configuration
--------------------------
When two drives are daisy-chained on the host interface, one must be
designated at the master drive (C: drive) and one as the slave drive
(D: drive). Commands from the host are written in parallel to both
drives.

When the C/D jumper on the drive is closed, the drive will assume the
role of a master. When C/D is open, the drive will act as a slave. In
single-drive configurations, C/D must remain in the closed (master)
position.

Cable Select
------------
This optional method of drive master/slave designation can be enabled
by jumper selection as described below. If used, special cabling can
be used to selectively ground the CSEL interface signal of the
drive intended to be drive C (0). This drive will then function as
the master. If CSEL is allowed to float the drive will recognize it-
self as drive D (1) and function as the slave.













TOP
previous page: Hard Drive: SEAGATE: ST352X 42MB 3.5"/SL    IDE / XT
  
page up: Hard Drive Specs from SEAGATE
  
next page: Hard Drive: SEAGATE: ST3543A      FILEPRO 541MB 3.5"/SL    ATA2 FAST