S T 3 4 5 5 5 W SEAGATE
Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 6311| | |
Capacity form/unform 4550/ 6500 MB Heads 8| | |
Seek time / track 10.5/ 1.3 ms Sector/track | | |
Controller SCSI3 SI/WI/FA Precompensation
Cache/Buffer 512 KB Landing Zone
Data transfer rate 11.000 MB/S int Bytes/Sector 512
40.000 MB/S ext SYNC
Recording method PRML 0/4/4,ZBR operating | non-operating
-------------+--------------
Supply voltage - Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g 10 | 75
seek W Rotation RPM 7200
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 800000
Warranty Month
Lift/Lock/Park YES Certificates
SEAGATE ST34555W JUMPER SETTING
REAR VIEW
(TOP) J1 Auxiliary
+-------------------+ +-- -1++---------+
-+ |||||||||||||||||1+-|::::::|| X X X X +-
+-------------+-----+ +++++++++-5-G-G-12+
68 pin I/O Cable+ ||||||
Connection Male ||||||
|||||| SCSI ID = 0 (none)
Auxiliary option header |||||+-- SCSI ID = 1
||||+--- SCSI ID = 2
pin-11 +5v ---------+||+---- SCSI ID = 4
pin-10 GND ----------++---+- SCSI ID = 8
+-- or pin-8 Activity LED
Side View
FRONT TOP (HDA) J2 87654321 +--
OF ---------------------------------P-W-A------+J1
DRIVE BOTTOM :::::::: +--
||||||||
Enable T-Res (W model only) +||||||+ Terminator Power|
Start Delay (12 secs * ID) -+||||+- Terminator Power++
Motor Start --+||+-- Reserved |
Write Protect ---++--- Parity Disable |
|
+--------------------------------+ |
| Termination Power-source Table +------------------+
+--------------------------------+-------------+
| -----....-----....-----PWA edge-----|
| 2 1 2 1 2 1 |
| o X X o o o |
| o X X o xxx |
| A B C |
+----------------------------------------------+
A = Drive Supplies Bus
B = Drive Supplies Own
C = Bus Supplies Drive
A + B is valid!
FRONT VIEW
+--+RESERVED! Shipped with cover
| | installed.
| +Do not remove. Do not install jumpers
TOP (HDA) ++---+ 1
-P-W-A---------------------+::::|::::::+--
* BOTTOM +----+123456
| J6 ||||||
LED -+ ||||||
Remote LED +||||+ ID 1
(pin-11 +5v) |||+- ID 2
Reserved -+|+-- ID 4
+--- ID 8
Caution: Do not use J2 jumpers on J6. The internal contacts
will be bent and cannot be reused on J2 without them
falling off.
SCSI ID ------- +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | ID8 | ID4 | ID2 | ID1 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+