Hard Drive: SEAGATE: ST32430WD HAWK 2LP 2147MB 3.5"/SL SCSI2 D/W
S T 3 2 4 3 0 W D H A W K 2 L P SEAGATE
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 3898| | |
Capacity form/unform 2147/ 2600 MB Heads 9| | |
Seek time / track 9.8/ 1.5 ms Sector/track | | |
Controller SCSI2 DI/WI/FAST Precompensation
Cache/Buffer 512 KB LOOK-AHEAD Landing Zone
Data transfer rate 5.000 MB/S int Bytes/Sector 512
20.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 70
Power: sleep W Humidity % |
standby W Altitude km |
idle 6.5 W Shock g |
seek W Rotation RPM 5411
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 800000
Warranty Month 60
Lift/Lock/Park YES Certificates
Layout
SEAGATE ST32430W/3620W PRODUCT DESCRIPTION
+---------------------------------------------------------+ | |XX1 | |XXPower | |1-+ | || J5 ++LED || | ++ |+-+ | |+1+ | ||X|I/O | ||X| | ||X| | ||X|J1 | ||X| |+-+ ||X| || |J6 ||X| |+-1 8--------1 ||X| | +--------+J2 |+-+ +---------------------------------------------------------+
Jumpers
SEAGATE ST32430W/3620W PRODUCT DESCRIPTION
Jumper Setting
==============
REAR VIEW +------ 5V
| +---- GND
(TOP) | | +-- GND
34 1 1 | | | + 12V
+---------------------+ +-J5---+ +-------+
----+|||||||||||||||||||||+--+::::::+-+O O O O+-
+---------------------+ +------+ +-------+
68pin I/O Cable |||||| Power SCSI ID = 0 (none)
Connection |||||+----------- SCSI ID = 1
||||+------------ SCSI ID = 2
|||+---------+--- SCSI ID = 4 or pin-6
||| +--- REFIND+
||+-------------- SCSI ID = 8
|+--------------- pin-10 GND
+---------------- pin-11 +5V
J5 SCSI ID ----------- +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | 7-8 | 5-6 | 3-4 | 1-2 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+
RIGHT SIDE VIEW
+-J1 TOP (HDA)
|X+------------+--------+-----PWA--------------------Front of drive
+-+ |12345678|J2
+--------+
+Terminator PWR -+||||||+- RESERVED
+Terminator PWR --+||||+-- Start Delay (12 secs * ID)
| Enable T-Res ---+||+--- Motor Start
| Parity Enable ----++---- Write Protect
|
|
Terminator Power-source Table
-----------------------------
1 2 1 2 1 2
+---- +---- +----
|X o |o X |o o
|X o |o X |xxx
+------ +------ +-------
Drive Supplies Drive Supplies Bus Supplies
Bus Own Drive
FRONT VIEW J6
TOP (HDA) +-----1+
-------PWA--------------------------------+::::::+---
++ +------+ SCSI ID = 0 none
++LED pin-11 +5V --+||||+-- SCSI ID = 1
pin-10 GND ---+||+--- SCSI ID = 2
SCSI ID = 8 or -+--++--+- SCSI ID = 4 or
pin-8 BUSY -+ +- pin-6 REFIND+
NOTE
If these ID jumper are used, the ID jumpers J5 ARE NOT USED!!!!!
J6 SCSI ID ----------- +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | 7-8 | 5-6 | 3-4 | 1-2 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+
Features
SEAGATE ST32430W/WD/WC/DC/31230W/WD/WC/DC INSTALL. GUIDE 77767478
Before you begin
----------------
Verify that the system is switched off and disconnected from main
power before any installation is attempted.
Protect yourself, the drive, and your valuable programs and data by
reading the following cautions and warnings.
- Do not tamper with sealed top cover. Doing so voids your warranty. The drive contains no user serviceable components. See Product Repair section for more information.
- Visually inspect the shipping container for any obvious damage.
- Verify all parts listed on shipping bill are received with the equipment. Discrepancies or damage should be reported to the shipping company.
- Inspect drive for possible shipping damage. All claims of this type should be filed promptly with the transporter involved. Save original packing materials to be used when reshipping.
- When transporting or shipping a drive or system, please ensure that they are correctly packed in original Seagate approved (or equivalent) container and shipped via an airride carrier experienced in handling computer equipment.
- Do not unpack drive from its static shielded bag until you are ready to install it in the system.
- Always handle the drive by the frame or casting.
- Do not touch Printed Circuit Board (PCB) or the I/O connector pins.
- Never apply pressure to the PCB or to the drive top cover.
Caution. The circuit assemblies and components contained in this
equipment can be degraded or destroyed by Electrostatic Overstress
(EOS) or by Electrostatic Discharge (ESD).
Static electrical charges can accumulate quickly on personnel,
clothing and synthetic materials. The electrostatic fields due to
these charges when brought in close proximity to susceptible circuit
assemblies and components, can result in degraded reliability or
immediate failure of the affected component or assembly.
To insure optimum reliable equipment operation, it is required that
technical support personnel discharge themselves by wearing a
grounding strap around the wrist and be connected to a grounding
terminal while working in the vicinity of, and while handling EOS/
ESD susceptible assemblies/parts. If unavailable, ground yourself
frequently by touching the metal chassis of the system before
handling any components (this helps only if the system is connected
to a ground). Avoid static-inducing carpeted areas. This procedure
is especially important when handling printed circuit boards (PCB's).
Safety instructions
-------------------
1. The disc drive(s) are to be installed in a customer supplied
enclosure where the surrounding air does not exceed 50 o C.
2. Four (4) 6-32 UNC-2A screws are required for installation. Maximum
screw length into side of drive is 0.15 inches (3.81 mm). Maximum
screw length into bottom is 0.20 in. (5.08 mm). Maximum screw
tightening torque is 6.0 in-lb (.675 NM) with minimum thread
engagement of 0.12 in (3.05 mm).
3. The power requirements are shown in the Product Information
section.
4. The power supply must satisfy the safety requirements for SELV
(Safety Extra Low Voltage) cir-cuits.
5. Service is to be provided by trained Seagate service personnel.
6. The incorporation of the disc drives listed in this guide into a
customer enclosure must meet the appropriate safety requirements
of the country in which it is used (e.g. UL 1950, CAN/CSA-C22.2
No. 950-M89, DIN VDE 0805:1993 and EN60950: 1992 (IEC 950).
Note. Power must be off when connecting or disconnecting.
- CMOS configuration: SCSI drives should not be defined in the CMOS. The SCSI host adapter uses its own BIOS to handle the Input/Output procedures.
The CMOS setting for SCSI drive is either drive type zero, or the no
drive installed option.
Low-Level formatting: All Hawk 2LP wide family drive models are
low-level formatted at the factory and do not require this step
during installation. If an installed drive is low-level formatted,
all user data will be lost.
Note: Seagate Technology assumes no liability for lost user data.
Partitioning and high level formatting: A drive can be subdivided
into "partitions" which behave as individual drives within the
system. Consult the system documentation for instructions on
partitioning and high level formatting. Information is also available
in bookstores and libraries.
Product repair information
--------------------------
Service requirements
The special facilities required for the manufacture of these drives
generally prohibit repair in the field. If problems occur during
installation, please contact your supplier for assistance. Do not
attempt to disassemble or repair. Drives should be sent to the repair
depot through the purchase source, if possible. Please observe
the following cautions.
Caution! - Handle drive with care. Do not drop, or bump hard. - Never remove the cover of these disc drives. Servicing items in the sealed HDA (heads, media, actuator, etc.) require special facilities. The drive contains no user purchasable parts or PCBs. - Opening the sealed HDA voids the drive warranty. - Applying a soldering device to the components on the PCB voids the drive warranty. - Do not connect or disconnect cables without first removing power from the drive. - Place drive on a flat, static dissipative surface and handle with extreme care. Always follow all EOS/ESD precautions to avoid damage to the electrical assemblies.
Shipping
When transporting or shipping a drive, a Seagate approved container
must be used. Keep your original box. They are easily identified by
the Seagate Approved Package label. Shipping a drive in a
non-approved container voids the drive warranty.
Seagate repair centers may refuse receipt of components improperly
packaged or obviously damaged in transit. Contact your Authorized
Seagate Distributor to purchase additional boxes. Seagate recommends
shipping by an air-ride carrier experienced in handling computer
equipment.
Initial setup information
-------------------------
For the initial setup connect the cables or plug into a mounted
connector (if applicable), set the drive ID on the bus and enable or
disable the I/O line terminator resistor packs (Hawk 2LP family "W"
models only).
These procedures are described in paragraphs following.
Note whether drive model number ends in W, WD, WC or DC.
Write precompensation and reduced write current
-----------------------------------------------
Not required on Seagate SCSI Interface drives covered by this manual.
Do not power up the host system until the drive is mounted and the
system cover is replaced.
Connect DC power connector to the drive ("W/WD" models only).
Replace the Host System cover.
Turn on DC power.
Boot the system from the floppy drive or from a previously installed
hard-drive if there is one.
Proceed with drive setup of the new hard drive.
SCSI interface drives
---------------------
The SCSI interface handles both drive geometry and defect management
internally. The "no drive installed" option is selected for systems
with SCSI drives.
All SCSI interface drives are low-level formatted at the factory. You
may wish to low-level format the drive to optimize its performance
for your system. Consult the controller documentation for information
on low-level formatting. Partitioning and high-level formatting can
be done through DOS by way of the FDISK utility for partitioning, and
FORMAT for high-level formatting.
Consult your DOS manual for FORMAT and FDISK command options.
My Books
