Hard Drive: SEAGATE: ST19171W BARRACUDA 9 9100MB 3.5"/HH SCSI3 W/UL
S T 1 9 1 7 1 W B A R R A C U D A 9 SEAGATE
Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 5333| | |
Capacity form/unform 9100/11700 MB Heads | | |
Seek time / track 9.0/ 1.0 ms Sector/track | | |
Controller SCSI3 SI/WI/ULTR/FAS Precompensation
Cache/Buffer 512 KB MULTI-SEGMEN Landing Zone
Data transfer rate 8.500 MB/S int Bytes/Sector 512
20.000 MB/S ext
Recording method PRML 0/4/4 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 70
Power: sleep W Humidity % |
standby W Altitude km |
idle 12.4 W Shock g |
seek W Rotation RPM 7200
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 1000000
Warranty Month 60
Lift/Lock/Park YES Certificates
Layout
SEAGATE ST19171W/WD INSTALLATION GUIDE 83329020 REV. A 2/96
+---------------------------------------+----------1------+ 1-+ +----------+J2 |XX | |J6 |XXI | | |XXN | | |XXT +-+ W MODELS |XXE | |XXR | |XXF | |XXA | |XXC | 1XXE | |12+ | || | J1 | || | | |+-1 | |XX Power | |XX +---------------------------------------------------------+ 1
Jumpers
SEAGATE ST19171W/WD INSTALLATION GUIDE 83329020 REV. A 2/96
Jumper Setting
==============
J6 Setting the SCSI ID jumpers
------------------------------
Use the J6 connector to set the SCSI ID. To change the SCSI ID,
install jumpers on the appropriate pins as shown. Optional
connections to switching circuits in host equipment are provided on
J1 auxiliary to set the SCSI ID.
|
---+--------+----------------+-+
| * * * *|. . . . * * * 1 |
| * * * *|. . . . * * * * |J6
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * * 1 |
| * * * *|* * * * * * * * |J6 SCSI ID 0
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * * X |
| * * * *|* * * * * * * X |J6 SCSI ID 1
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * X 1 |
| * * * *|* * * * * * X * |J6 SCSI ID 2
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * X X |
| * * * *|* * * * * * X X |J6 SCSI ID 3
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X * 1 |
| * * * *|* * * * * X * * |J6 SCSI ID 4
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X * X |
| * * * *|* * * * * X * X |J6 SCSI ID 5
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X X 1 |
| * * * *|* * * * * X X * |J6 SCSI ID 6
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X X X |
| * * * *|* * * * * X X X |J6 SCSI ID 7
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X * * 1 |
| * * * *|* * * * X * * * |J6 SCSI ID 8
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X * * X |
| * * * *|* * * * X * * X |J6 SCSI ID 9
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X * X 1 |
| * * * *|* * * * X * X * |J6 SCSI ID 10
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X * X X |
| * * * *|* * * * X * X X |J6 SCSI ID 11
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X X * 1 |
| * * * *|* * * * X X * * |J6 SCSI ID 12
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X X * X |
| * * * *|* * * * X X * X |J6 SCSI ID 13
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X X X 1 |
| * * * *|* * * * X X X * |J6 SCSI ID 14
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * X X X X |
| * * * *|* * * * X X X X |J6 SCSI ID 15
+--------+----------------+
+--- SCSI ID A3
| +- SCSI ID A2
| | +SCSI ID A1
--68PIN-----+-----J1-+-+---+-------+
* * * * 1|* * * * * * 1 |POWER |
* * * * |12* * * * * * |X X X X|
----------+------------+-+-------1
+SCSI ID A0
J1 Pin 2 = Fault LED
J1 Pin 4 = Vendor Unique
J1 Pin 6 = Spindle Sync
J1 Pin 8 = Activity LED
J1 Pin 9+12 = No Connection
J1 Pin 10 = Ground
J1 Pin 11 = +5V
Pins 2, 4, 6, and 8 are driven low for 250ms after PWR ON and reset
to allow jumper selectable SCSI ID.
J2 Terminating the drive
------------------------
ST19171W drives are terminated with permanently mounted IC active
terminators. If you install one of these drives and it is not on the
end of the SCSI bus, disable the terminators by removing the jumper
from pins 15 and 16 of connector J2. If you install the drive on the
end of the SCSI bus, enable termination by installing a jumper on
pins 15 and 16 of connector J2.
+---------------+
--+* * * * * * * 1+-- J2
* * * * * * * *
T D M W P E T T
E S E P D S P P
+---------------+
--+X . . . . . . 1+-- J2 Enable SCSI terminator (default)
X . . . . . . . ST19171W only
+---------------+
--+* . . . . . . 1+-- J2 Disable SCSI terminator
* . . . . . . .
NOTE
Use active (ANSI SCSI-2 Alternative 2) terminators when terminating
the bus.
ST19171WD drives do not have internal terminators or any other way
of adding internal termination to the drive. You must provide
external differential termination to these drives when termination is
required.
Terminator Power
----------------
There are three posiible terminator power configurations for ST19171W
drives. You will not normally need to change this option and can
leave the drive configured as it was shipped from the factory.
ST19171W
+---------------+
--+. . . . . . X 1+-- J2 Terminator Power from Drive (DEFAULT)
. . . . . . X *
+---------------+
--+. . . . . . * X+-- J2 Terminator Power to SCSI Bus
. . . . . . * X
+---------------+
--+. . . . . . * 1+-- J2 Terminator Power from SCSI BUS
. . . . . . xxx
ST19171WD
+---------------+
--+. . . . . . * X+-- J2 Terminator Power to SCSI Bus (DEFAULT)
. . . . . . * X
+---------------+
--+. . . . . . * *+-- J2 Host adapter or other device provides
. . . . . . * * terminator power to external terminator.
Other applicable jumper options
-------------------------------
+---------------+
--+. . . . . * . 1+-- J2 RESERVED
. . . . . * . .
Delay Motor Start option
------------------------
Delay Motor Start option (valid only if the Enable Motor Start
jumper is not connected)
+---------------+
--+. * . . . . . 1+-- J2 Disable the Delay Motor Start option
. * . . . . . . (default)
+---------------+
--+. X . . . . . 1+-- J2 Motor start delay equal to the SCSI ID
. X . . . . . . multiplied by 12 seconds. For example, if
the SCSI ID = 2, the drive starts in 24
seconds.
Motor Start option
------------------
+---------------+
--+. . * . . . . 1+-- J2 Disable motor start (default). The drive
. . * . . . . . starts according to the Delay Motor Start
Option.
+---------------+
--+. . X . . . . 1+-- J2 Enable motor start. The drive waits for the
. . X . . . . . Start Unit command from the host before
starting the spindle motor.
Write Protect Option
--------------------
+---------------+
--+. . . * . . . 1+-- J2 Write protect = Off (enables writing -
. . . * . . . . default)
+---------------+
--+. . . X . . . 1+-- J2 Write protect = ON (disables writing)
. . . X . . . .
Parity Check Option
-------------------
+---------------+
--+. . . . * . . 1+-- J2 Enables parity check of SCSI bus (default)
. . . . * . . .
+---------------+
--+. . . . X . . 1+-- J2 Disables parity check
. . . . X . . .
J6 Jumper Options
-----------------
|
---+--------+----------------+-+
| * * * *|. * * . . . . 1 |
| * * * *|. * * . . . . . |J6 RESERVED
+RESERVED+----------------+
|
---+--------+----------------+-+
| * * * *|* . . . . . . 1 |
| * * * *|* . . . . . . . |J6 Remote LED
+RESERVED+----------------+
REAR VIEW (ST-19171W only)
(TOP) Auxiliary
------------------- +-----1++---------+
---( +++++++++++++++++1)-+::::::++ O O O O +---
\------------|----/ +------++-5-G-G-12+
68 pin I/O Cable+ |||||| V V
Connection Male ||||||
||||||
||||||
Auxiliary option header ||||||
pin-11 +5V ---------+|||||
pin-10 GND ----------+||||
SCSI ID = 8 -----------+|||
SCSI ID = 4 ------------+||
or pin-6 REFIND+ ------+||
SCSI ID = 2 -------------+|
SCSI ID = 1 --------------+
SCSI ID = 0 (none)
REAR VIEW (ST-19171WC only)
80 pin I/O and DC Power Wall/bracket Connection
| Female
J1 /----|---------------\ TOP (HDA)
-----------/ ++++++++++++++++++++ \------------
(--1------------------40-) BOTTOM
Notes on 80 pin I/O connector:
pins 1 - 4 = +12V 41 - 44 = 12V GND
34 - 36 = +5V 74 - 76 = 5V GND
37 = SYNC 77 = LEDC
38 = MTRON 78 = DLYDST
39 = SCSIA0 79 = SCSIA1
40 = SCSIA2 80 = SCSIA3
Mating NC connector: AMP US p/n: 2-557103-1 straight-in, Male 80-pin
2-557101-1 right angle to PCB
SIDE VIEW (ST-19171W/WC)
BACK +-+ J2 12345678 TOP (HDA) FRONT
OF J1+------------------------------------------------- OF
DRIVE +-+ :::::::: BOTTOM DRIVE
||||||||
|Terminator Power +||||||+ Enable T-Res (not used on WC,WD models)
++Terminator Power -+||||+- Start Delay (12 secs * ID)
| Reserved --+||+-- Motor Start
| Parity Disable ---++--- Write Protect
|
|
| +--------------------------------+
+-+ Termination Power-source Table |
+--------------------------------+-------------------------+
|xxxxx....xxxxx....xxxxxPWAxedgexxxxx |
| A Drive Supplies Bus |
| 1 2 1 2 1 2 1 2 B Drive Supplies Own |
| C Bus Supplies Drive |
| X * * X * * xxx D Differential only: |
| x * * x xxx * * Drive Supplies Bus |
| A B C D |
+---------Default------------------------------------------+
(not used on WC model)
Note: WD drives do not have internal terminators or any other
way of adding internal terminators to the drive; use
external active termination if required.
FRONT VIEW (ST-19171W/WC)
+--+Reserved. Shipped with cover installed.
| +Do not remove. Do not install jumpers
TOP (HDA) ++---+-----1+
--------PWA-------------+::::|::::::+---
x BOTTOM +----+123456+
| J6 ||||||
LED -+ ||||||
Remote LED +||||+ ID 1
(pin-11 +5V) |||+- ID 2
RESERVED -+|+-- ID 4
+--- ID 8
General
SEAGATE SUPPORT SERVICES
Seagate Technology
------------------
Technical Support Services
If you need assistance installing your drive, consult your dealer.
Dealers are familiar with their unique system configurations and can
help you with system conflicts and other technical issues. If you
need additional assistance with your Seagate(r) drive or other
Seagate products, use one of the Seagate technical support services
listed below.
SeaFONE at 1-800-SEAGATE (1-800-732-4283)
Seagate's 800 number allows toll-free access to automated self-help
services, providing answers to commonly asked questions,
troubleshooting tips and specifications for disc drives and tape
drives. This service is available 24 hours daily and requires a
touch-tone phone. If you need to speak to a technical support
engineer, dial this number and listen to the options for technical
support. (International callers can also reach this automated
self-help service by dialing 408-456-4496).
Seagate Technology online services
Using a modem, you can obtain troubleshooting tips, free utility
programs, drive specifications and jumper settings for Seagate's
entire product line. You can also download software for installing
and analyzing your drive.
SeaNET
You can obtain technical information on Seagate drives, Seagate
software and much more over the Internet from Seagate's World Wide
Web home page (http://www.seagate.com) or Seagate's ftp server
(ftp://ftp.seagate.com).
You may also send E-mail with your questions to DiscSupport@
Seagate.com or TapeSupport@Seagate.com.
SeaBOARD
SeaBOARD is a computer bulletin board system (BBS) that contains
information about Seagate's disc and tape drive products and is
available 24 hours daily. Set your communications software to eight
data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers
are listed in the following table.
BBS Location Modem number
United States Disc: 408-434-1080; Tape: 408-456-4415
England 44-1628-478011
France 33 1-48 25 35 95
Germany 49-89-140-9331
Singapore 65-292-6973
Thailand 662-531-8111
Australia 61-2-9756-2359
Taiwan 886-2-719-6075
Seagate CompuServe forum
Online technical support for Seagate products is available on
CompuServe. To access our technical support forum, type go seagate.
This forum provides information similar to that found on SeaBOARD.
In addition, you can type questions or browse through previous
questions and answers on the forum messages.
Seagate Technology FAX services
SeaFAX
You can use a touch-tone telephone to access Seagate's automated FAX
system to receive technical support information by return FAX. This
service is available 24 hours daily.
Location Telephone number
United States 1-800-SEAGATE or 408-456-4496
England 44-1628-894084
Australia 61-2-9756-5170
Seagate technical support FAX
You can FAX questions or comments to technical support specialists 24
hours daily. Responses are sent during business hours.
Location FAX number
United States 408-944-9120
England 44-1628-890660
France 33 1-46 04 42 50
Germany 49-89-1430-5100
Australia 61-2-9725-4052
Singapore 65-293-4722
Hong Kong 852-2368 7173
Taiwan 886-2-715-2923
Korea 82-2-556-7294/4251
Seagate technical support
You can talk to a technical support specialist during business hours
Monday through Friday for one-on-one technical help. Before calling,
note your system configuration and drive model number (STxxxx). There
are several technical support phone numbers available for various
Seagate products.
Location Telephone number
United States Please dial 1-800-SEAGATE for the specific product
telephone number.
(6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M.,
Pacific time, M-F)
England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to
5:00 P.M., M-F)
France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00
P.M. to 5:00 P.M., M-F)
Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00
P.M. to 4:00 P.M., M-F)
Tape: 49-89-140-9333
Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F)
Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00
P.M. to 5:00 P.M., M-F)
Hong Kong 852-2368 9918
Taiwan 886-2-514-2237
Korea 82-2-556-8241
SeaTDD 408-944-9121
Using a telecommunications device for the deaf (TDD), you can send
questions or comments 24 hours daily and exchange messages with a
technical support specialist between 6:00 A.M. to 11:15 A.M. and
12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday.
Customer Service Centers
Seagate direct OEM, Distribution, System Integrator and Retail
customers should contact your Seagate Service Representative for
warranty information. Other customers contact your place of
purchase. Seagate offers comprehensive customer support for all
Seagate drives. Seagate customer service centers are the only
facilities authorized to service Seagate drives. These services are
available worldwide.
Location Telephone number FAX number
United States 1-800-468-3472; 405-949-6740
Other Americas
(Canada & Brazil) 405-949-6706; 405-949-6738
Mexico 525-546-6965; 525-546-4888
Europe, Middle
East & Africa 31-2065-43300; 31-2065-34320
Asia Pacific &
Australia 65-485-3595; 65-485-4980
Japan 81-3-5462-2904; 81-3-3462-2979
Seagate, Seagate Technology and the Seagate logo are registered
trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD,
SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or
registered trademarks of Seagate Technology, Inc. or one of its
subsidiaries. All other trademarks or registered trademarks are the
property of their respective owners.
My Books
