Hard Drive: SEAGATE: ST19171N BARRACUDA 9 9100MB 3.5"/HH SCSI3 ULTR
S T 1 9 1 7 1 N B A R R A C U D A 9 SEAGATE
Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 5333| | |
Capacity form/unform 9100/11700 MB Heads | | |
Seek time / track 9.0/ 1.0 ms Sector/track | | |
Controller SCSI3 SI/ULTR/FA Precompensation
Cache/Buffer 512 KB MULTI-SEGMEN Landing Zone
Data transfer rate 8.500 MB/S int Bytes/Sector 512
10.000 MB/S ext
Recording method PRML 0/4/4 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 70
Power: sleep W Humidity % |
standby W Altitude km |
idle 12.4 W Shock g |
seek W Rotation RPM 7200
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 1000000
Warranty Month 60
Lift/Lock/Park YES Certificates
Layout
SEAGATE ST19171N/ND INSTALLATION GUIDE 83329020 REV. A 2/96
+---------------------------------------+----------1------+ 1-+ +----------+J2 |XX | |J6 |XXI | | |XXN | | |XXT +-+ N/ND MODEL |XXE | |XXR | |XXF | |XXA | |XXC | |XXE | |XX | |XX | |XX | | 1 | |XX Power | |XX +---------------------------------------------------------+ 1
Jumpers
SEAGATE ST19171N INSTALLATION GUIDE 83329020 REV. A 2/96
Jumper Setting
==============
J6 Setting the SCSI ID jumpers
------------------------------
Use the J6 connector to set the SCSI ID. To change the SCSI ID,
install jumpers on the appropriate pins as shown.
|
---+--------+----------------+-+
| * * * *|* * * * * * * 1 |
| * * * *|* * * * * * * * |J6
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * * 1 |
| * * * *|* * * * * * * * |J6 SCSI ID 0
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * * X |
| * * * *|* * * * * * * X |J6 SCSI ID 1
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * X 1 |
| * * * *|* * * * * * X * |J6 SCSI ID 2
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * * X X |
| * * * *|* * * * * * X X |J6 SCSI ID 3
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X * 1 |
| * * * *|* * * * * X * * |J6 SCSI ID 4
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X * X |
| * * * *|* * * * * X * X |J6 SCSI ID 5
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X X 1 |
| * * * *|* * * * * X X * |J6 SCSI ID 6
+--------+----------------+
---+RESERVED+----------------+
| * * * *|* * * * * X X X |
| * * * *|* * * * * X X X |J6 SCSI ID 7
+--------+----------------+
J2 Terminating the drive
------------------------
ST19171N drives are terminated with permanently mounted IC active
terminators. If you install one of these drives and it is not on the
end of the SCSI bus, disable the terminators by removing the jumper
from pins 15 and 16 of connector J2. If you install the drive on the
end of the SCSI bus, enable termination by installing a jumper on
pins 15 and 16 of connector J2.
+---------------+
--+* * * * * * * 1+-- J2
* * * * * * * *
T D M W P E T T
E S E P D S P P
+---------------+
--+X . . . . . . 1+-- J2 Enable SCSI terminator (default)
X . . . . . . .
+---------------+
--+* . . . . . . 1+-- J2 Disable SCSI terminator
* . . . . . . .
Terminator Power
----------------
There are three posiible terminator power configurations for ST19171N
drives. You will not normally need to change this option and can
leave the drive configured as it was shipped from the factory.
+---------------+
--+. . . . . . X 1+-- J2 Terminator Power from Drive (DEFAUlLT)
. . . . . . X *
+---------------+
--+. . . . . . * X+-- J2 Terminator Power to SCSI Bus
. . . . . . * X
+---------------+
--+. . . . . . * 1+-- J2 Terminator Power from SCSI BUS
. . . . . . xxx
Other applicable jumper options
-------------------------------
+---------------+
--+. . . . . * . 1+-- J2 RESERVED
. . . . . * . .
Delay Motor Start option
------------------------
Delay Motor Start option (valid only if the Enable Motor Start
jumper is not connected)
+---------------+
--+. * . . . . . 1+-- J2 Disable the Delay Motor Start option
. * . . . . . . (default)
+---------------+
--+. X . . . . . 1+-- J2 Motor start delay equal to the SCSI ID
. X . . . . . . multiplied by 12 seconds. For example, if
the SCSI ID = 2, the drive starts in 24
seconds.
Motor Start option
------------------
+---------------+
--+. . * . . . . 1+-- J2 Disable motor start (default). The drive
. . * . . . . . starts according to the Delay Motor Start
Option.
+---------------+
--+. . X . . . . 1+-- J2 Enable motor start. The drive waits for the
. . X . . . . . Start Unit command from the host before
starting the spindle motor.
Write Protect Option
--------------------
+---------------+
--+. . . * . . . 1+-- J2 Write protect = Off (enables writing -
. . . * . . . . default)
+---------------+
--+. . . X . . . 1+-- J2 Write protect = ON (disables writing)
. . . X . . . .
Parity Check Option
-------------------
+---------------+
--+. . . . * . . 1+-- J2 Enables parity check of SCSI bus (default)
. . . . * . . .
+---------------+
--+. . . . X . . 1+-- J2 Disables parity check
. . . . X . . .
J6 Jumper Options
-----------------
|
---+--------+----------------+-+
| * * * *|. * * . . . . 1 |
| * * * *|. * * . . . . . |J6 RESERVED
+RESERVED+----------------+
|
---+--------+----------------+-+
| * * * *|* . . . . . . 1 |
| * * * *|* . . . . . . . |J6 Remote LED
+RESERVED+----------------+
Install
SEAGATE ST19171N/ND BARRACUDA 9 INSTALLATION GUIDE 83329020 REV. A
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
Features
SEAGATE ST19171N/W/WD/WC/DC INSTALLATION GUIDE 83329020 REV. A
Preface
-------
This manual contains information for users of the Seagate ST19171
Barracuda 9 SCSI disc drives. It provides support services,
performance specifications, and initial setup information.
Electrostatic discharge protection
----------------------------------
Caution.
Removal of circuit boards by personnel not performing depot
repair will damage components and may void the warranty.
All drive electronic assemblies are sensitive to static electricity,
due to the electrostatically sensitive devices used within the drive
circuitry. Although some devices such as metaloxide semiconductors
are extremely sensitive, all semiconductors, as well as some
resistors and capacitors, may be damaged or degraded by exposure
to static electricity.
Electrostatic damage to electronic devices may be caused by the
direct discharge of a charged conductor or by exposure to the
static fields surrounding charged objects. To avoid damaging drive
electronic assemblies, observe the following precautions when
installing or servicing the drive:
- Ground yourself to the drive whenever the drive electronics are or will be exposed. Connect yourself to ground with a wrist strap (Seagate part number 12263496). Connection may be made to any grounded metal assembly. As a general rule, remember that you and the drive electronics must all be grounded to avoid potentially damaging static discharges.
- Turn off the power before removing or installing the DC power cable.
- Do not remove any circuit boards from the drive.
- Never use an ohmmeter on any circuit boards.
- When installing the drive on a carrier or tray, discharge the static electricity from the carrier or tray prior to inserting it into the system.
Important safety information and precautions
--------------------------------------------
Caution. Use forced-air ventilation when bench testing the drive to
ensure proper cooling of drive components.
Use proper safety and repair techniques for safe, reliable operation
of this unit. Service should be done only by qualified persons.
The procedures in this manual and labels on the unit contain warnings
and cautions that must be carefully read and followed to minimize or
eliminate the risk of personal injury. The warnings point out condi-
tions or practices that may endanger you or others. The cautions
point out conditions or practices that may damage the unit, possibly
making it unsafe for use.
Always observe the following warnings and precautions:
- Perform all maintenance by following the procedures in this manual.
- Follow all cautions and warnings in the procedures.
- Use sound safety practices when operating or repairing the unit.
- Use caution when troubleshooting a unit that has voltages present. Turn off power to the unit before servicing it.
- Wear safety shoes when removing or replacing heavy parts.
- Ensure that the internal temperature of the rack or cabinet does not exceed the limits defined for the drive when the drive is mounted in an equipment rack or cabinet. When units are stacked vertically, pay special attention to the top where temperatures are usually highest.
- Do not remove any circuit boards from the drive chassis. Return the entire drive for depot repair if any circuit board is defective. Removal of circuit boards by personnel not performing depot repair will damage components and may void the warranty.
- Do not remove the head and disc assembly (HDA) from the drive chassis. Return the entire drive for depot repair if the HDA is defective.
- Do not attempt to disassemble the HDA. It is not field repairable. If the sealed HDA is opened by personnel not performing depot repair, this will damage compo-nents and void the warranty.
As a component, this drive is designed to be installed and operated
in accordance with UL1950, IEC950, EN60950, CSA C22.2 950, and
VDE0805.
Typical applications of these disc drives include customer packag-
ing and subsystem design. Safety agencies conditionally certify
component assemblies, such as the Barracuda disc drive, based on
their final acceptability in the end-use product. The subsystem
designers are responsible for meeting these conditions of accept-
ability in obtaining safety, regulatory agency compliance in their
end-use products and for certifying where required by law. A
necessary part of meeting safety requirements is the provision
for overcurrent protection on drive SELV supply voltages.
This unit is a component part and as such is not meant to comply
with FCC or similar national requirements as a standalone unit.
Engineering radiated emissions test results are available through
the Seagate Safety Department to assist the subsystem designer.
General description
-------------------
Barracuda 9 SCSI disc drives are high-speed, randomaccess digital-
data storage devices.
The drive is a component for installation in an enclosure designed
for the drive. This is often a rack within the system or an external
enclosure designed to house one or more disc drives or other
peripheral units. In either case, the disc drive must receive
adequate cooling and it must be sufficiently grounded and
shielded from emissions.
General
SEAGATE SUPPORT SERVICES
Seagate Technology
------------------
Technical Support Services
If you need assistance installing your drive, consult your dealer.
Dealers are familiar with their unique system configurations and can
help you with system conflicts and other technical issues. If you
need additional assistance with your Seagate(r) drive or other
Seagate products, use one of the Seagate technical support services
listed below.
SeaFONE at 1-800-SEAGATE (1-800-732-4283)
Seagate's 800 number allows toll-free access to automated self-help
services, providing answers to commonly asked questions,
troubleshooting tips and specifications for disc drives and tape
drives. This service is available 24 hours daily and requires a
touch-tone phone. If you need to speak to a technical support
engineer, dial this number and listen to the options for technical
support. (International callers can also reach this automated
self-help service by dialing 408-456-4496).
Seagate Technology online services
Using a modem, you can obtain troubleshooting tips, free utility
programs, drive specifications and jumper settings for Seagate's
entire product line. You can also download software for installing
and analyzing your drive.
SeaNET
You can obtain technical information on Seagate drives, Seagate
software and much more over the Internet from Seagate's World Wide
Web home page (http://www.seagate.com) or Seagate's ftp server
(ftp://ftp.seagate.com).
You may also send E-mail with your questions to DiscSupport@
Seagate.com or TapeSupport@Seagate.com.
SeaBOARD
SeaBOARD is a computer bulletin board system (BBS) that contains
information about Seagate's disc and tape drive products and is
available 24 hours daily. Set your communications software to eight
data bits, no parity and one stop bit (8-N-1). SeaBOARD phone numbers
are listed in the following table.
BBS Location Modem number
United States Disc: 408-434-1080; Tape: 408-456-4415
England 44-1628-478011
France 33 1-48 25 35 95
Germany 49-89-140-9331
Singapore 65-292-6973
Thailand 662-531-8111
Australia 61-2-9756-2359
Taiwan 886-2-719-6075
Seagate CompuServe forum
Online technical support for Seagate products is available on
CompuServe. To access our technical support forum, type go seagate.
This forum provides information similar to that found on SeaBOARD.
In addition, you can type questions or browse through previous
questions and answers on the forum messages.
Seagate Technology FAX services
SeaFAX
You can use a touch-tone telephone to access Seagate's automated FAX
system to receive technical support information by return FAX. This
service is available 24 hours daily.
Location Telephone number
United States 1-800-SEAGATE or 408-456-4496
England 44-1628-894084
Australia 61-2-9756-5170
Seagate technical support FAX
You can FAX questions or comments to technical support specialists 24
hours daily. Responses are sent during business hours.
Location FAX number
United States 408-944-9120
England 44-1628-890660
France 33 1-46 04 42 50
Germany 49-89-1430-5100
Australia 61-2-9725-4052
Singapore 65-293-4722
Hong Kong 852-2368 7173
Taiwan 886-2-715-2923
Korea 82-2-556-7294/4251
Seagate technical support
You can talk to a technical support specialist during business hours
Monday through Friday for one-on-one technical help. Before calling,
note your system configuration and drive model number (STxxxx). There
are several technical support phone numbers available for various
Seagate products.
Location Telephone number
United States Please dial 1-800-SEAGATE for the specific product
telephone number.
(6:00 A.M. to 11:15 A.M., 12:30 P.M. to 5:00 P.M.,
Pacific time, M-F)
England 44-1628-894083 (10:00 A.M. to 1:00 P.M., 2:00 P.M. to
5:00 P.M., M-F)
France 33 1-41 86 10 86 (9:30 A.M. to 12:30 P.M., 2:00
P.M. to 5:00 P.M., M-F)
Germany Disc: 49-89-140-9332; (9:30 A.M. to 12:30 P.M., 2:00
P.M. to 4:00 P.M., M-F)
Tape: 49-89-140-9333
Australia 61-2-9725-3366 (9:00 A.M. to 5:00 P.M., M-F)
Singapore 65-290-3998 (9:00 A.M. to 12:00 P.M., 2:00
P.M. to 5:00 P.M., M-F)
Hong Kong 852-2368 9918
Taiwan 886-2-514-2237
Korea 82-2-556-8241
SeaTDD 408-944-9121
Using a telecommunications device for the deaf (TDD), you can send
questions or comments 24 hours daily and exchange messages with a
technical support specialist between 6:00 A.M. to 11:15 A.M. and
12:30 P.M. to 5:00 P.M. (Pacific time) Monday through Friday.
Customer Service Centers
Seagate direct OEM, Distribution, System Integrator and Retail
customers should contact your Seagate Service Representative for
warranty information. Other customers contact your place of
purchase. Seagate offers comprehensive customer support for all
Seagate drives. Seagate customer service centers are the only
facilities authorized to service Seagate drives. These services are
available worldwide.
Location Telephone number FAX number
United States 1-800-468-3472; 405-949-6740
Other Americas
(Canada & Brazil) 405-949-6706; 405-949-6738
Mexico 525-546-6965; 525-546-4888
Europe, Middle
East & Africa 31-2065-43300; 31-2065-34320
Asia Pacific &
Australia 65-485-3595; 65-485-4980
Japan 81-3-5462-2904; 81-3-3462-2979
Seagate, Seagate Technology and the Seagate logo are registered
trademarks of Seagate Technology, Inc. SeaFAX, SeaFONE, SeaBOARD,
SeaTDD, SeaNET, Medalist and DiscWizard are either trademarks or
registered trademarks of Seagate Technology, Inc. or one of its
subsidiaries. All other trademarks or registered trademarks are the
property of their respective owners.
My Books
