lotus

previous page: Hard Drive: QUANTUM: DSP-2022A 220MB 2.5"/SSL   IDE / AT
  
page up: Hard Drive Specs from QUANTUM
  
next page: Hard Drive: QUANTUM: DSP-3053L 535MB 3.5"/SL    SCSI2 FAST

Hard Drive: QUANTUM: DSP-2022S 220MB 2.5"/SSL SCSI2 FAST




D S P - 2 0 2 2 S    QUANTUM
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders    1393|     |     |
Capacity form/unform   220/  260 MB        Heads           5|     |     |
Seek time   / track  10.0/ 2.0 ms          Sector/track     |     |     |
Controller           SCSI2 SI/FAST         Precompensation
Cache/Buffer           512 KB SEGMENTED    Landing Zone
Data transfer rate    4.000 MB/S int       Bytes/Sector      512
                     10.000 MB/S ext SYNC
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 60
Power: sleep          0.5 W     Humidity     %        10 90    |      8 95
       standby        1.5 W     Altitude    km                 |
       idle           4.5 W     Shock        g        10       |    100
       seek           5.0 W     Rotation   RPM      5400
       read/write         W     Acoustic   dBA        34
       spin-up            W     ECC        Bit   88,REED SOLOMON
                                MTBF         h     250000
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

DEC DSP2022S SPECIFICATION SUMMARY

  +---------------------------------------------------------+
  |                                     +-+0                |XX
  |                                     | |                 |XX
  |                                     | |J1               |XX
  |                                     | |                 |XX I
  |                                     +-+7                |XX N
  |                                                         |XX T
  |                                                         |XX E
  |                                                         |XX R
  |                                                         |XX F
  |                                                         |XX A
  |                                                         |XX C
  |                                                         |XX E
  |                                                         |XX
  |                                                         |XX
  |                                                         |XX
  |                                                         |
  +---------------------------------------------------------+

      +----------------------------------------------------+
      |                                                    |
      |                                                    |
      +----------------------------------------------------+
      |+-----------------------------------------A7-----A1+|
      ||39 o o o o o o o o o o   o o o o o o o 1  o o o o ||
      ||40 o o o o o o o o o o o o o o o o o o 2  o o o o ||
      |+-----------------------------------------A8-----A2+|
      +-------------SCSI-----------------------------------+
      +                                           +-+-+-+  +

                                                  Vendor Specific
                                                  Options (4 x 2 pin)

Jumpers

DEC DSP2022S SPECIFICATION SUMMARY

Jumper Setting
==============

x = Factory setting

 J1 Drive ID
 -----------
 Connector J1 on the drive module is used to select drive configura-
 tion options. The connector has eight jumper pin pairs numbered 0
 through 7. Each selection is made by placing a jumper across opposing
 pins.
        0 1 2 3 4 5 6 7
       +-+-+-+-+-+-+-+-+J1
       +-+-+-+-+-+-+-+-+

  +-------+--------------------------------------------------------+
  |Jumper | Descriptions                                           |
  +-------+--------------------------------------------------------+
  |   0   | Device Address bit 0                                   |
  +-------+--------------------------------------------------------+
  |   1   | Device Address bit 1                                   |
  +-------+--------------------------------------------------------+
  |   2   | Device Address bit 2                                   |
  +-------+--------------------------------------------------------+
  |   3   | Jumper in place enables automatic spin up when power   |
  |       | is applied. When the jumper is removed it disables     |
  |       | automatic spin up.                                     |
  +-------+--------------------------------------------------------+
  |   4   | Jumper in place disabled the spin-delay timer. When the|
  |       | jumper is removed, it enables the spin-delay timer. The|
  |       | delay is equal to 10 second times the SCSI ID address. |
  |       | The delay is valid only when automatic spin up is      |
  |       | enabled.                                               |
  +-------+--------------------------------------------------------+
  |   5   | RESERVED                                               |
  +-------+--------------------------------------------------------+
  |   6   | RESERVED for Manufacturing tests. Remove this jumper to|
  |       | prevent manufacturing tests from being initiated if pin|
  |       | A1 is grounded.                                        |
  +-------+--------------------------------------------------------+
  |   7   | Jumper in place enables drive power to an external SCSI|
  |       | bus terminator. Remove the jumper to disable this power|
  |       | source.                                                |
  +-------+--------------------------------------------------------+

 J1  Selection of Device Address by Jumpers 2,1,0
 ------------------------------------------------
   +----------+-----------------------+
   | SCSI ID  |        Jumpers        |
   |          |   2   |   1   |   0   |
   +----------+-------+-------+-------+
   |    7     | OPEN  | OPEN  | OPEN  |
   |    6     | OPEN  | OPEN  | CLOSED|
   |    5     | OPEN  | CLOSED| OPEN  |
   |    4     | OPEN  | CLOSED| CLOSED|
   |    3     | CLOSED| OPEN  | OPEN  |
   |    2     | CLOSED| OPEN  | CLOSED|
   |    1     | CLOSED| CLOSED| OPEN  |
   |  x 0     | CLOSED| CLOSED| CLOSED|
   +----------+-------+-------+-------+

Your drive unit is shipped with all the jumpers in place. This means
that the device address is present to 0. To alter the device address,
use jumpers 0 through 2 according to the table below.

 SCSI Vendor-Specific Pins
 -------------------------
 +---+--------------+------------------------------------------------+
 |Pin|Signal Name   |Functions                                       |
 +---+--------------+------------------------------------------------+
 |A1 |RESERVED      |Leave open                                      |
 +---+--------------+------------------------------------------------+
 |A2 |RESERVED      |Leave open                                      |
 +---+--------------+------------------------------------------------+
 |A3 |RESERVED      |Leave open                                      |
 +---+--------------+------------------------------------------------+
 |A4 |RESERVED      |Leave open                                      |
 +---+--------------+------------------------------------------------+
 |A5 |SCSI ID Bit 0 |Least significant bit of encoded SCSI ID number |
 +---+--------------+------------------------------------------------+
 |A6 |SCSI ID Bit 1 |Middle bit of encoded SCSI ID number            |
 +---+--------------+------------------------------------------------+
 |A7 |SCSI ID Bit 2 |Most significant bit of encoded SCSI ID number  |
 +---+--------------+------------------------------------------------+
 |A8 |ACTIVITY LED  |Drives an external activity LED. (Active low,   |
 |   |              |+5V, 24 ma).                                    |
 +---+--------------+------------------------------------------------+

Remote Device Address Selection by SCSI Connector
-------------------------------------------------
When all three jumpers (0-2) are left in place for ID=0, the drive
will use any acitve encoded SCSI ID number on the vendor-specific
conncetor at the rear of the drive. If there is not an active ID
address on pins A5-A7, the drive will assume the ID is 0.

Remote SCSI ID
--------------

           PINS      |
       A7   A6   A5  | SCSI ID
       MSB       LSB |
       --------------+--------
       1    1    1   |    0
       1    1    0   |    1
       1    0    1   |    2
       1    0    0   |    3
       0    1    1   |    4
       0    1    0   |    5
       0    0    1   |    6
       0    0    0   |    7

1 = TTL high
0 = TTL low

Activity LED Signal
-------------------
There is not a Light Emitting Diode (LED) located on the drive.
However, the Activity LED signal on pin A8 of the vendor-specific
portion of the SCSI connector may be used to drive an external LED.
When the LED is on, it indicates the drive is processing SCSI
commands from the host.

SCSI Terminators
----------------
The DSP2022S drive does not have SCSI bus termination on it. Bus
termination is must be accomplished externally. If you leave jumper
7 in place, the drive will supply power for bus termination through
the SCSI cable pin 24. Remove this jumper if you do not need this
cable termination power from the drive. Termination is needed only at
the ENDS of the SCSI bus.

 J1 Power
 --------
 Pin 37 Ground, Motor return
 Pin 38 Ground, Motor return
 Pin 39 +5V, Motor power
 Pin 40 +5V, Motor power

Install

DEC DSP2022S SPECIFICATION SUMMARY

Notes On Installation
=====================

SCSI Connector Location
-----------------------
The interface connector is located on the electronic module side of
the drive. It consists of two rows of 25 pins on 2 mm centers.

SCSI Interface Cable
--------------------
A standard 0.1 inch SCSI flat ribbon cable may be attached to the
drive through an adapter made by 2.5 inch disk drive vendors.

A 1 mm flat ribbon cable may also be used with a suitable 2 x 25, 2
mm IDC connector (e.g. Molex 87259-5016). Use the 1 mm cable with the
following caution.

CAUTION
It is recommended that only one disk drive be powered from a given
segment of 1 mm cable.













TOP
previous page: Hard Drive: QUANTUM: DSP-2022A 220MB 2.5"/SSL   IDE / AT
  
page up: Hard Drive Specs from QUANTUM
  
next page: Hard Drive: QUANTUM: DSP-3053L 535MB 3.5"/SL    SCSI2 FAST