Hard Drive: MICROPOLIS: 1664-7 344MB 5.25"/HH ESDI
1 6 6 4 - 7 MICROPOLIS
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/HH Cylinders 1780| | |
Capacity form/unform 344/ 389 MB Heads 7| | |
Seek time / track 15.0/ 4.0 ms Sector/track 54| | |
Controller ESDI Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate 1.875 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 50 | -40 65
Power: sleep W Humidity % 10 90 | 10 90
standby 12.8 W Altitude km -0.061 3.048| -0.305 15.240
idle W Shock g 2 | 40
seek W Rotation RPM 3600
read/write 14.3 W Acoustic dBA 43
spin-up W ECC Bit
MTBF h 150000
Warranty Month 12
Lift/Lock/Park YES Certificates
Layout
MICROPL. 1660 SERIES TECHNICAL MANUAL 106546 REV. A/106474 REV. B
Part No. 106602-xx-x
+---------------------------------------------------------+
| +-+-+-+-+-+-+-+-+ (J12 Not Used)|XX J12
| +-+-+-+-+-+-+-+-+ |
| W1W2W3W4W5DA3DA2DA1 |XX
| |XX
| |XX J2
| |X1
| COMPONENT SIDE |
| |XX
| Interface +-RN1|XX
| Terminator| | |XX
| | | |XX
| | | |XX J1
| +-+ |X1
| |
| Frame Gr.+W14|XX
| ++ |X1 J3
+---------------------------------------------------------+ Power
(Solder Side)
+---------------------------------------------------------+
| +-+-+-+-+-+-+-+-+ (J12 Reserved)|XX J12
| +-+-+-+-+-+-+-+-+ |
| W1W2W3W4W5DA3DA2DA1 |XX
| |XX
| |XX J2
| |X1
| COMPONENT SIDE |
| |XX
| Interface +-RN1|XX
| Terminator| | |XX
| | | |XX
| W13 | | |XX J1
| ++-+ +-+ |X1
| ++-+ LED |
|W12 Frame Gr.+W14|XX
| ++ |X1 J3
+---------------------------------------------------------+ Power
(Solder Side)
+--------------------------------------+
| +--+J4 |
| HDA +--+ Frame +--+J5 |
| Ground+--+ |
| |
| J3 |
| J2 J1 XXXXXXXX|
| ........ XXXXXXXXXXXXXXXXXX Power |
+--Data---1------Signal------1--------1+
Connector Connector
Jumpers
MICROPL. 1660 SERIES TECHNICAL MANUAL 106546 REV. A/106474 REV. B
Jumper Setting
==============
x = Jumper set at factory
Drive Select DA3/DA2/DA1 ------------------------- +--------+------------------------+ |Drive | Select Jumpers | |Address | DA3 DA2 DA1 | +--------+------------------------+ |x 1 | OPEN OPEN CLOSED | | 2 | OPEN CLOSED OPEN | | 3 | OPEN CLOSED CLOSED | | 4 | CLOSED OPEN OPEN | | 5 | CLOSED OPEN CLOSED | | 6 | CLOSED CLOSED OPEN | | 7 | CLOSED CLOSED CLOSED | +--------+------------------------+
Drive Address 0 is used as a "deselect" (i.e., no drive is selected).
The three Drive Select interface lines are decoded to select the
correspondingly addressed drive to the host controller/formatter. In
multiple-drive systems, each drive must have its own unique address.
Terminator Pack RN1 provides proper termination for the interface
lines. When daisy-chaining the 1660 drives, the terminator is
installed only in the last drive on the daisy chain.
W1 Hard- or Soft-sectored mode
-------------------------------
CLOSED The drive is configured to operate in the SOFT SECTOR
mode. Address mark generation and detection are enabled,
and the Sector/Address Mark Found interface signal is
used to report address mark found. Sector size is
selected by the host controller.
x OPEN The drive is configured to operate in the HARD SECTOR
mode. The Sector/Address Mark Found interface signal is
used to transmit sector pulses to the host controller.
Sector pulses are derived from the servo disk. The number of sector
pulses generated is equal to:
+ +
|31,248| Where 31,248 = byte clock derived from servo
INT|------| disk
| n | INT = integer part of
+ + n = the number of unformatted bytes/
sector (82 minimum)
W2/W3/W4 Hard Sector Configuration
-----------------------------------
+--------+---------------------------+------------------------+
|Sectors | Bytes/Sector | Jumpers |
| | Formatted Unformatted | W4 W3 W2 |
+--------+---------------------------+------------------------+
| 53 | 512 588 | OPEN OPEN OPEN |
| x 54 | 512 576 | OPEN OPEN CLOSED|
| 28 | 1024 1116 | OPEN CLOSED OPEN |
| 14 | 2048 2232 | OPEN CLOSED CLOSED|
| 7 | 4096 4464 | CLOSED OPEN OPEN |
| - | Reserved | CLOSED OPEN CLOSED|
| 97 | 256 321 | CLOSED CLOSED OPEN |
| 1 | 31248 31248 | CLOSED CLOSED CLOSED|
+--------+---------------------------+------------------------+
The number of bytes/sector may be specified using the Set Bytes Per
Sector command or by selecting a sector configuration with option
jumpers W2, W3, and W4.
Note that the factory default sector configuration is 54 sectors (W2
installed, W3 and W4 not installed).
Other combinations of sector numbers and bytes per sector are avail-
able; contact Micropolis Product Support for details.
W5 Spindle Control Option
--------------------------
CLOSED The drive must wait for a Start Spindle command to start
the spindle motor.
x OPEN The drive automatically starts the spindle motor at
power-on. (Factory default configuration)
W12/W13 LED (for 1664-7)
------------
A jumper is installed at W12 or W13 to select the color of the LED.
When a jumper is installed at W12, the red LED is selected.
When a jumper is installed at W13 (the factory default configura-
tion), the green LED is selected.
W14 Frame Ground Option
------------------------
CLOSED Frame ground is connected to logic ground.
x OPEN Frame ground is not connected to logic ground
J3 DC Power and pin connector assignments
-------------------------------------------
+------------+ pin 1 +12 V
| 1 2 3 4 | pin 2 +12 V Return
+------------+ pin 3 + 5 V Return
pin 4 + 5 V
J12 RESERVED!
Install
MICROPL. 1660 SERIES TECHNICAL MANUAL 106549 REV. A/106474 REV.B
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
Dimensions and Mounting
-----------------------
The 1660 Series uses industry-standard mounting for 5 -inch
half-height Winchester disk drives.
Recommended orientation is vertical on either side, or horizontal
with the Device Electronics board down; other mounting orientations
may be used provided the ambient air temperature around the drive is
kept at or below 50*C (122*F).
Inasmuch as the drive frame acts as a heat sink to dissipate heat
from the unit, the enclosure and mounting structure should be
designed to allow natural convection of heat around the HDA and
frame. If the enclosure is small and/or natural air flow is
restricted, a fan may be required. In any case, no point on the HDA
assembly should exceed 62*C (143*F).
Mounting Screws
---------------
4 per side 6-32 UNC-2B x 0.10 deep (thru hole).
4 on bottom 6-32 UNC-2B x 0.22 deep
Caution: To avoid restricting HDA sway space, the mounting screws must not penetrate the outer surface of the side mounting holes more than .10 (+.00, -.03) inch or the bottom mounting holes by more than .20 (+.00, -.03) inch. Torque applied to the screws must not exceed 8 in-lbs.
Control Signal Connector J1
---------------------------
J1 is a 34-pin board-edge connector. The signals on this connector
control the drive and transfer drive status to the host controller.
Recommended Cable: 3M Scotchflex 3365/34 or equivalent.
Mating connector: AMP 88373-3 (key slot between pins 4 and 6).
J2 Data Tranfer Connector
-------------------------
J2 is a 20-pin board-edge connector. The signal on this connector
contain read or write data.
Recommended Cable: 3M Scotchflex 3365/20.
Mating Connector: AMP 88373-6 (key slot between pins 4 and 6).
J3 DC Power Connector ---------------------- J3 is a 4-pin, keyed, AMP MATE-N-LOCK connector. This connector supplies DC power (+5V and +12V) to the drive.
Mating Connector: AMP 1-480424-0
Pins: AMP 350078-4
Suggested Wire Size: 18 AWG
Ground Connectors J4 and J5
---------------------------
3/16-inch spade lugs J4 and J5 are provided for grounding.
System characteristics determine the proper ground connection.
Mating connector: AMP 60972-2 or equivalent.
Daisy-chaining the 1660 Drive
-----------------------------
Host Controller
+------------+ +---------------+
| TERMINATORS+--CONTROL---o-----+ J1 Drive #1 |
| | +---------+-----+ J2 |
| | | | +--+ J3 J4/J5 |
| | | | | +-------+-------+
| | | | | +-------------+
| | | | | +---------------+ |
| | | o--+--+ J1 Drive #2 | |
| | | +------+--+--+ J2 | |
| | | | | o--+ J3 J4/J5 | |
| | | | | | +-------+-------+ |
| | | | | | +-------------o
| | | | | | +---------------+ |
| | | | o--+--+ J1 Drive #3 | |
| | | | +--+--+--+ J2 | |
| | | | | | o--+ J3 J4/J5 | |
| | | | | | | +-------+-------+ |
| +--+ | | | | +-------------o
| DATA +-----+ | | | +---------------+ |
| +---------+ +--+--+ J1 Drive #4 | |
| +---------------+--+ J2 +----+ |
| | o--+ J3 J4/J5| T | |
+------------+ | +-------+--+----+ |
| | |
DC VOLTAGES -------------+ | |
GROUND ------------------------o-------------+
T = TERMINATORS
Interface Terminator RN1 is installed ONLY in the last physical
drive in the control chain.
Connectors J4 and J5 are provided for grounding; system character-
istics determine the proper ground connection.
Up to seven disk drives may be connected to a single host controller/
formatter. The control signal at J1 are transmitted via the standard,
daisy-chain interconnection. The data signals at J2 are transmitted
via radially connected data-transfer lines.
Interface Electrical Characteristics
------------------------------------
Connector J1
The Control Signals control the drive and transfer drive status to
the host controller. The signals are low-true at the interface, high-
true into drivers and out of receivers, and have the following logic
levels.
Driver: 7438 or equivalent Receiver: 74LS14 or equivalent
True = 0.0 VDC to 0.40 VDC @ I = -48 milliamps (maximum) False = 2.5 VDC to 5.25 VDC @ I = +250 microamps (open collector)
Interface Cable Length 10 feet (3 meters) maximum
Connector J2
All interface data transfer signals are differential in nature.
One TTL control signal and four TTL status signal are also provided
at Connector J2.
The signals are high true into drivers and out of receivers and have
the EIA RS-422 levels shown.
Driver: AMD 26LS31 or equivalent Receiver: AMD 26LS32 or equivalent
High = +2V Low = +0.5V
Adjustments and Maintenance
---------------------------
The 1660 disk drives requires no adjustments or periodic
maintenance; additionally, no mechanical adjustments are required to
prepare a system for handling or shipment.
Field-Replacable Components
---------------------------
The concept of repair by replacement of complete functional
components is utilized in the 1660 Series, resulting in an MTTR of
less than 15 minutes.
Features
MICROPL. 1660 SERIES TECHNICAL MANUAL 106549 REV. A/106474 REV. B
Interface
---------
The 1660 disk drives are pin- and function-compatible with the
Serial mode of the Enhanced Small Device Interface (ESDI) for 5 1/4-
inch Winchester disk drives. In the Serial mode, interface signals
(control, data, and status) are transmitted serially via handshaking
request/acknowledge signals.
Media Defects
-------------
Media defects are physical characteristics of the media which result
in repetitive read error when a functional drive is operated within
specified operating conditions.
At the time of manufacture, a media test system evaluates every drive
and identifies each media defect location. The defects are logged on
a label affixed to the drive. The defective areas are identified by
head address (HD), cylinder address (CYL), and number of Bytes From
Index (BFI). A printed listing of the defects is also shipped with
each drive.
In addition to listing the defects on the label and the printout, the
defects are also mapped on the drive. The defect list is written for
each data surface. The list is written on the corresponding surface
in Sector 0 at three cylinder locations:
1) The maximum cylinder (1779).
2) The maximum cylinder minus 8 (1771).
3) A special cylinder accessed as "Cylinder 4095" (FFFh).
Note: The cylinder at the address of 4095 is a drive-unique location.
This is in compliance with the industry-standard ESDI
specification. Do not attempt to write to Cylinder 4095.
Micropolis specifies that all 1660 drives shall have no more than
one defect per megabyte of unformatted capacity. Additionally,
Cylinder 0 and the cylinder at 4095 shall be defect-free at the time
of shipment.
Seek Time
---------
| 1660 |
----------------------------------+--------+
Track-to-Track msec. typ. | 4 |
Average msec. typ. | 14 |
msec. max | 30 |
One-Third Stroke msec. max. | 15 |
Latency msec. avg. | 8.33 |
Nominal msec. max. | 16.67 |
----------------------------------+--------+
My Books
