Hard Drive: MAXTOR: XT-3380 319MB 5.25"/FH SCSI1 SE
X T - 3 3 8 0 MAXTOR
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 1224| | |
Capacity form/unform 319/ 383 MB Heads 15| | |
Seek time / track 27.0/ 4.0 ms Sector/track 34| | |
Controller SCSI1 SINGLE-ENDED Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate 1.500 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g |
seek W Rotation RPM 3600
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 20000
Warranty Month
Lift/Lock/Park YES Certificates
Layout
MAXTOR XT-3380 OEM MANUAL 1011005 REV. C
+---------------------------------------------------------+ | 1++ |XX | || |XX | ++ |XX | Terminators 1++ |XX | || |XX | JP3 E5 E3 JP1 ++ |XX | JP2-++-+-+-+-+-+-+-+ 1++ |XX | +-++-+ | | | +-+ | || |XX | E4+-+E2-+ +-E1 JP91 - 88 ++ |XX | +++++ JP10-+| | +++++ JP16-++-11 | +JP9 : | | | | ++ : | | | | JP6+--+ JP12-+ | | JP5| +--+JP8 +--+ | JP4+--+--+JP7 |XX | |XX Power +------------------------------------------------------+
Jumpers
MAXTOR XT-3380 OEM MANUAL 1011005 REV. C
Jumper Setting
==============
x = Jumpers set at factory
Jumpers JP1, JP2, JP3, JP4, JP5, JP6, JP9, JP88, JP89, JP90, JP91 are
for Manufature Test ONLY, they are NOT USER SELECTABLE and are
shipped CLOSED.
JP7: Write Protect
JP8: Immediate Motor Spin Up Option
JP10, JP11: Terminator Power Selection
JP12, JP13, JP14: SCSI Controller ID
JP15: Parity Enable
JP16: Power On Spindle delay Option
E1: Adjacent pin E1 is a ground point
JP12/13/14 SCSI ID
-------------------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | JP14 | JP13 | JP12 |
+----------+-------+-------+-------+
Lowest-----|x --0 | OPEN | OPEN | OPEN |
+----------+-------+-------+-------+
| 1 | OPEN | OPEN | CLOSED|
+----------+-------+-------+-------+
| 2 | OPEN | CLOSED| OPEN |
+----------+-------+-------+-------+
| 3 | OPEN | CLOSED| CLOSED|
+----------+-------+-------+-------+
| 4 | CLOSED| OPEN | OPEN |
+----------+-------+-------+-------+
| 5 | CLOSED| OPEN | CLOSED|
+----------+-------+-------+-------+
| 6 | CLOSED| CLOSED| OPEN |
+----------+-------+-------+-------+
Highest----|----7 | CLOSED| CLOSED| CLOSED|
Priority +----------+-------+-------+-------+
As shipped from the factory, all jumpers are open, giving the XT-3000
a priority value/ID of zero.
In multiple SCSI device configuration, it is necessary to configure
each device with a priority. The priority identification for each
drive is determined by the three binarily weighted ID jumpers. An ID
of 7 is the highest priority in a multidevice configuration.
JP7 Write Protect
------------------
CLOSED Data cannot be written to the drive, only read opera-
tions can be executed.
x OPEN Allowing normal reading and writing.
JP8/JP16 Spin On Power/Delay/Command ------------------------------------- JP8 OPEN JP16 OPEN With both jumpers removed (OPEN) the drive will not spin-up until the Host issues a Start/Stop command (1BH) with the Start Bit = 1.
JP8 OPEN JP16 CLOSED With JP8 removed (OPEN) and JP16 installed (CLOSED), the drive spins-up after exhausting a 13 second per SCSI ID delay.
JP8 CLOSED JP16 OPEN With JP8 installed (CLOSED) and JP16 removed (OPEN), the drives spins-up immediately when power is applied.
JP10/JP11 Terminator Power --------------------------- JP10 OPEN JP11 CLOSED The terminator power is external from the SCSI bus.
JP10 CLOSED JP11 OPEN x The terminator power is internal from the drive.
JP15 SCSI bus parity
---------------------
x JP15 CLOSED Enables odd parity detection.
OPEN Disables odd parity detection.
As shipped from the factory the XT-3000 detects parity. Odd parity is
always generated.
Install
MAXTOR XT-3000 OEM MANUAL 1011005 REV. C
Interface Termination
---------------------
As shipped, all assigned interface signal lines are terminated with a
removable 220/330 ohm resistor network. The first device and the last
device on the daisy-chain SCSI bus must be terminated. Remove the
terminators from any devices in between. For instance, if the XT-3000
is in the middle of the string, remove its terminators. Any host
adapters beeing used should be terminated in a similar fashion.
The devices driving the drive inpute should be open collector devices
capable of sinking at least 48 milliamps at a voltage level of less
than 0.5 VDC (7438 or equivalent).
Devices receiving the drive outputs should be of "SCHMITT" trigger
type to improve noise immunity, 74LS14, 74LS240 or equivalent. The
host adapter should not load the bus with more than one standard
LSTTL input load per line, and should terminate the drive output
signals with 220/330 ohm terminators.
Features
MAXTOR XT-3000 OEM MANUAL 10111005 REV. C
Seek Time
---------
| XT3170 | XT3380 |
| XT3280 | |
----------------------------------+--------+--------+
Track-to-Track msec. typ. | 4 | 4 |
Average msec. typ. | 30 | 27 |
Average msec. max. | 54 | 52 |
----------------------------------+--------+--------+
Includes settling
Reliability Specifications
--------------------------
MTBF 20,000 POH, typical usage
PM Not required
MTTR 30 minutes
Component Design Life 5 years
Formatted Capacity
------------------
XT-3170/XT-3280
+------------+--------+-------+--------+
|Bytes/Sector| 256 | 512 | 1024 |
+------------+--------+-------+--------+
|Sector/track| 46 | 26 | 14 |
+------------+--------+-------+--------+
|MB | 129,72 | 146,64| 157,93|
+------------+--------+-------+--------+
XT-3380
+------------+--------+-------+--------+
|Bytes/Sector| 256 | 512 | 1024 |
+------------+--------+-------+--------+
|Sector/track| 59 | 34 | 18 |
+------------+--------+-------+--------+
|MB | 277,31 | 319,61| 338,41|
+------------+--------+-------+--------+
General
MAXTOR SCSI INSTALLATION
GENERIC INSTALLATION PROCEDURE FOR A SCSI DRIVE
-----------------------------------------------------------
1. Install a 50 pin ribbon connector making sure pin 1, which
can be identified by the striped edge of the cable, is closest
to the power connector on the drive.
2. Install a DC power cable to the back of the drive.
3. Verify the SCSI ID selection.
Note: SCSI ID usually needs to be set to 0 to be the boot drive.
The last physical device on the SCSI bus must be terminated.
Any other drive or SCSI device connected between the host and
the device at the end of the bus must not be terminated.
4. Apply power to the computer.
4a. When memory test is complete go into your system's Standard
C-MOS set-up.
(Note: There are various ways to get into C-MOS set-up,
please refer to system's manual for instuctions.)
4b. Set the drive type to "Not Installed". This intelligent drive
will identify itself to the SCSI host adapter.
5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
it. At the A> prompt type in FDISK. At the menu options select
option 1 to create a DOS partition. Another menu will appear and
from those options choose 1 to create a Primary DOS partition.
Select yes to make 1 large partition and it will automatically
become active. Then escape from FDISK.
6. At the A> prompt type in FORMAT C:/S
This does a high-level format on the drive and transfers the
system files in order for the drive to be bootable.
(Note: Maxtor SCSI drives are low-level formatted at the factory)
7. The drive is now bootable. As a test remove the DOS diskette
from A and press reset to re-boot the computer, a C> should be
displayed, the drive is now ready for operation.
My Books
