H 3 1 7 1 - S 2 IBM NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/HH Cylinders | | | Capacity form/unform 163/ MB Heads | | | Seek time / track 10.7/ ms Sector/track | | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer 64 KB Landing Zone Data transfer rate MB/S int Bytes/Sector 512 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage Temperature *C | Power: sleep W Humidity % | standby W Altitude km | idle W Shock g | seek W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h Warranty Month Lift/Lock/Park YES Certificates
IBM H3133-S2/H3171-S2/H3256-S3/H3342-S4 JUMPER SETTING 8/1996
SCSI ID ------- +----------+-----------------------+ | SCSI ID | Jumpers | | | ID2 | ID1 | ID0 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+
TERM ON - Enables the on drive active termination
Auto Spin up - Enables drive automatically spin up when power is applied.
IBM SCSI INSTALLATION
SCSI Installation Guide Generic
To install a drive inside your computer or in an external storage
enclosure for SCSI devices, you must have:
1 The documentation that came with your computer or storage enclosure.
2 The documentation that came with your hard drive.
3 A small, flat blade screwdriver.
4 A SCSI controller, which is either built into the system board or on an adapter inside your computer.
5 An installation kit, if it is required for your computer. Contact your place of purchase if you are not sure.
6 If you are installing this into a PS/2 computer, you will also need the up-to-date backup copy of your reference diskette and diagnostic diskette.
WARNING: Do not open the static-protective bag containing the drive
until instructed to do so. Static electricity can damage the drive.
Hardware and software considerations
The operating system and hardware are two of the factors that
determine the number of drives a computer can support. The manuals
for your computer and operating system can help you to determine the
number and type of hard disk drives you can use.
Two factors that determine the number of internal drives that a
computer or SCSI storage enclosure can support are:
1 The available current of the power supply
2 The nominal operating current of each drive installed
Most computer power supplies have output over-current protection. If
the total allowed current is exceeded, the power supply shuts down.
The computer must be turned off and turned on again.
SCSI ID Each SCSI device connected to a SCSI adapter must be assigned
a unique SCSI identification number (ID). The ID you assign to this
device depends on the number of SCSI devices connected to the SCSI
adapter and the SCSI IDs already assigned to those devices.
Note: All IBM SCSI controllers support SCSI IDs 6 through 0. (ID 7 is
used for the SCSI controller.) Some SCSI controllers support SCSI IDs
15 through 8. If your SCSI controller supports more than seven
devices, then you can use SCSI IDs 15 through 8. If you are not sure
if your SCSI controller supports more than seven devices, refer to
the documentation that came with your SCSI controller for
If you have an IBM PS/2 computer, you can view your SCSI ID settings
by accessing the system programs. From the main menu, select Set
configuration. The select Set and view SCSI configuration.
Other computers might have utility programs that enable you to view
the SCSI configuration, or you might have to physically inspect the
installed SCSI devices to see how the IDs are set. For more
information, refer to the documentation that came with your computer
or SCSI controller.
1 Turn off all attached devices first; then turn off the computer.
2 Unplug all the power cords from electrical outlets before starting installation.
3 Disconnect all power cables from your computer and attached devices before starting installation.
4 Limit your movement. Movement can cause static electricity to build up around you.
5 Handle the drive carefully and by the edges.
6 Do not touch any exposed printed circuitry.
7 Prevent other people from touching the components or the drive.
8 When you are installing the drive, touch the static-protective package containing the drive to a metal expansion-slot screw or other unpainted metal surface on the computer, for at least 2 seconds. (This drains static electricity from the package and your body.)
9 When possible, remove the drive and install it directly into the computer without setting it down. If this is not possible, place the drive, component side up, on the static-protective bag on a flat surface until the drive is installed.
10 Do not place the drive on the computer cover or on a metal table.
Installing the drive
These instructions guide you as you install the drive inside your
computer or storage enclosure.
Step 1. Setting the jumpers and terminators
Note: Be sure you have chosen the SCSI ID before continuing. If you did not yet choose the SCSI ID, go to "SCSI IDs" above, then return here. Follow these steps to set the SCSI ID to match your chosen SCSI ID.
1 Touch the static-protective bag containing the drive to a metal expansionslot cover on the computer. This drains any static electricity from the package and your body.
2 Remove the drive from the static-protective bag, holding the drive by the edges. Do not touch any exposed components on the drive.
3 Place the drive on the bag, on a flat surface.
4 When the Auto Start feature is enabled, the hard disk drive motor starts as soon as the computer is turned on. Locate the Auto Start jumper by referring to the documentation that came with your drive. If the Auto Start jumper is not in place, the hard disk is started by a command from the SCSI controller. For drives installed in IBM computers or storage enclosures ensure that this jumper is off. The hard disk drive is started in a staggered sequence. This reduces the start-up load on the power supply. For non-IBM computer, refer to the documentation that came with your computer for further information.
5 Set the SCSI ID that you selected. To remove a jumper, pull it straight off. To install a jumper, line up the two holes in the jumper with the appropriate two pins on the drive. Then push the jumper onto the pins until it is completely seated and covers both pins.
6 Store any jumpers you do not use in a safe place, in case you need to change the SCSI ID for this drive later. WARNING: If you have extra jumpers, do not store them on any of the extra pins on the connector. Storing them on a set of pins could damage the drive.
Step 2. Connecting the terminator
The location of the drive you are installing inside the computer or
storage enclosure determines whether you need to connect a terminator
or put a jumper on the Enable Active Termination pins. Read the
information in the following table to determine if you must install
the terminator. For more information about termination, refer to the
documentation that came with your computer.
Note: A SCSI chain of devices consists of multiple SCSI devices
connected by a SCSI cable to a SCSI controller.
If the hard disk drive is: Then:
The last physical device on a SCSI chain of Install the terminator
devices inside the computer.
The last physical device on a SCSI chain of Install the terminator
devices inside an external storage enclosure.
Step 3. Enabling term power
If your drive has a jumper for term power and your SCSI controller is
suppling term power, (check with the manufacturer of your controller)
then you do not need to enable the term power. The jumper should be
off. For help in locating the term power jumper, refer to the
documentation that came with your drive.
Step 4. Installing the drive
For the specific information on installing a hard disk drive, refer
to the documentation that came with your computer. You will be
required to mount the drive inside your computer, and connect signal
and power cables to the hard drive. When installed in an enclosure,
the drive is attached by cable to the external connector of a SCSI
controller. The controller can be either on a SCSI adapter or built
into the system board inside of your computer.
Note: Be sure to use the correct screws provided with your drive.
Using the wrong ones might cause damage to the drive.
Step 5. Completing the installation procedure
The installation of the drive is complete. Reinstall the cover on the
computer or storage enclosure. Store these instructions and any extra
parts in a safe place in case you change your configuration.
After installing your hard disk drive, use the information that came
with your computer to reconfigure your system. When you power on your
system, turn on all attached devices first; then turn on the
If you have any problems at this point, turn off all attached
devices; then, turn off the computer and check that:
1 The cables are installed correctly
2 No options or cables are loose
3 The SCSI ID is properly set
4 No two SCSI drives have the same SCSI ID
5 The terminators are properly installed
Turn on all attached devices; then, turn on the computer. If you
still have a problem, refer to the troubleshooting information in the
documentation that came with your computer.
Step 6. Update configuration
Whenever you add or remove an option from your computer, you must
update the configuration information. Your computer might have an
automatic configuration program, or you might have to follow a
specific procedure. For more information, refer to the documentation
that came with your computer.
Step 7. Preparing the drive for use
Having successfully installed the hard disk drive, you need to
prepare it for use. Depending on the operating system you are using,
you might need to partition then format the hard disk. Refer to the
documentation that came with your operating system for information on
how to format your new drive. To make the drive just installed your
primary drive, you might need to create a new system partition on the
drive. For information on creating a new system partition, refer to
the documentation that came with your operating system.
You might be able to solve a problem yourself. Before calling IBM,
you might want to try some or all of the following troubleshooting
1 Remove and reattach all drive cables
2 Remove and reseat the drive
3 Place the drive in a different slot, if one is available
4 If your drive contains jumpers or switches, check that they are set as specified
5 Reread any software instructions; be sure software settings are correct
6 Inspect the drive for damage, such as bent pins
7 Check the computer manual for instructions about the installation of upgrades. Look for a section about system setup or system configuration. Follow all procedures.
8 After completing these steps, reassemble the computer and connect the power cord.
If you are still having problems and want to call IBM technical
support, have available as much of the following information as
1 Drive model or P/N and description
2 Computer manufacturer and model
3 Exact wording of error message (if any)
4 Description of the problem
5 Hardware and software configuration information for your system If possible, be at your computer. Your technical support rep might want to walk you through the problem during the call.