Hard Drive: IBM: DVAA-2810 TRAVELSTAR 810MB 2.5"/SSL ATA2 FAST

D V A A - 2 8 1 0   T R A V E L S T A R    IBM
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 2.5"/SUPERSLIMLINE    Cylinders        | 1571|     |
Capacity form/unform   810/      MB        Heads            |   16|     |
Seek time   / track  14.5/ 4.0 ms          Sector/track     |   63|     |
Controller           IDE / ATA2 FAST/ENHA  Precompensation
Cache/Buffer            32 KB WRITE CACHE  Landing Zone
Data transfer rate    3.000 MB/S int       Bytes/Sector      512
                      8.300 MB/S ext PIO3
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5 V          Temperature *C         5 55    |    -40 65
Power: sleep              W     Humidity     %         8 90    |      5 95
       standby            W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle           1.2 W     Shock        g        20       |    250
       seek               W     Rotation   RPM      3800
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit   128BIT REED SOLOMON,ON THE...
                                MTBF         h     300000
                                Warranty Month
Lift/Lock/Park     YES          Certificates     CSA,IEC950,TUV,UL1950        

Layout

IBM DVAA-2810 OEM FUNCTIONAL SPECIFICATIONS S66G-8103-00 1994

              +--------------------------------------+
              |                                      |
              |                                      |
              |                                      |
              +--------Interface-------------47------+
              |       **********************1 **45 Jumper
              |       *************x********* **46   |
              +------44----------------------48------+
              +                                      +

Pin position 20 is left blank for secure connector insertion.

Pin position 45 through 48 are used for drive address setting.

Jumpers

IBM DVAA-2810 OEM FUNCTIONAL SPECIFICATIONS S66G-8103-00 1994

Jumper Setting
==============

Drive Address Setting
---------------------
A jumper is available at the interface connector to determine the
drive address.

Using Cable Selection, the drive address depends on the condition of
pin 28 of the AT interface cable. In the case when pin 28 is ground
or low, the drive is a Master. If pin 28 is open or high level, the
drive is a Slave.

   ---47--45+
    *   * X | Master
    *   * X | (Default setting)
   ---48--46+

   ---47--45+
    *   * * | Slave
    *   * * | No Jumper
   ---48--46+

   ---47--45+
    *   * * | Cable Selection
    *   xxx |
   ---48--46+

Install

IBM DVAA-2810 OEM FUNCTIONAL SPECIFICATIONS S66G-8103-00 1994

Notes on Installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

 Mounting Orientation
 --------------------
 The disk drive shall operate in all axis (6 Directions). The disk
 drive shall operate within specified error rates when tilted +/-5
 degrees from these positions.

Performance and error rate must stay within specification limits if
the disk drive is operated in the other permissible orientations from
which it was formatted. Thus a disk drive formatted in a horizontal
orientation must be able to run vertically and vice versa.

 The recommended mounting screw torque is 3 +/- 0.5 kgf.cm.

 The recommended mounting screw depth is 3.5 +/- 0.5mm for bottom and
 5.0 +/- 0.5mm for horizontal mounting.

The system is reponsible for mounting the drive securely enough to
prevent from excessive motion or vibration of the drive at seek
operation or spindle rotation, using appropriate screws or equivalent
mounting hardware.

The vibration test and shock test are to be conducted with the
drive mounted to the table using bottom four screws.

Landing Zone and Lock
---------------------
A landing zone on the disk, not on the data area of the disk, is
provided to protect the disk data during shipping, movement, or
storage. After power down, a head locking mechanism secures the heads
in this zone.

Cabling
-------
The maximum cable length from the host system to the HDD plus
circuit pattern length in the host system shall not exceed 18 inches.

Interface Connector
-------------------
The signal connector for AT Attachment is designed to mate with
Dupont part number 69764-044 or equivalent.

 5V Power (Pins 41/42 of the Interface Connector)
 ------------------------------------------------
 There are two input pins for +5V power supply, +5V LOGIC, pin 41 and
 +5V MOTOR, pin 42. +5V LOGIC is connected to the internal logic
 circuits and +5V MOTOR is connected to the spindle motor and motor
 driver.

 It is possible to turn on and off +5V LOGIC by an external switch
 circuit to reduce power consumption to the least possible. In this
 mode, a voltage drop out due to the motor spin up current can be
 reduced by connecting +5V MOTOR line into the system power source
 directly.

If the above power management is used, all signal lines that will be
electrically active in the host system while the drive is
disconnected from power line shall be isolated by Three-State line
drivers. Internal leakage through ESD protection circuit may pull
down LPUL (least Positive Up Level) of logic signal below the spec.

Use both lines in parallel, for regular drive applications.

Features

IBM DVAA-2810 OEM FUNCTIONAL SPECIFICATIONS S66G-8103-00

Product Outline
---------------
- No-ID physical format

- ATA-2 interface

- CHS and LBA mode

- Enhanced ECC implementation

- Automatic retry on errors

- Self Diagnostics during Power On

- Power saving modes

- MR Head technology

- MCC standardized mounting holes and interface connector

- Closed Loop actuator servo

- Dedicated head landing zone

- Automatic actuator lock

- No preventive maintenance

Error Recovery
--------------
Errors occuring with the drive are handled by the error recovery
procedure.

Errors that are uncorrectable after of the error recovery procedures
are repported to the host system as non-recoverable errors.

Warranty
--------
The warranty will be covered by contracts.

Identification Labels
---------------------
The following labels are affixed to every drive.

 1. A label placed on the top of the HDA contains the statement "Made
    by IBM" or equivalent, Part number, and MLC number.

 2. A bar code label placed on the disk drive is based on user
    request. The location is to be designated in the drawing.

 3. Labels containing the vendor's name, disk drive model number,
    serial number, place of manufacture and UL/CSA certificates.

Except for the bar code, the labels may be integrated.

Interface Logic Signal Levels
-----------------------------
The interface logic signal have the following electrical
specifications:

 Inputs:   Input High Voltage       2.0 V min./ Vcc+0.7 V max
           Input Low Voltage        -0.5 V min./  0.8 V max.

 Outputs:  Output High Voltage     2.4 V min.
           Output Low Voltage      0.5 V max.

 Current:  Driver Sink Current     24 mA min.
           Driver Source Current   -400 uA min.