Hard Drive: IBM: DGVS-39110 (09U) 9100MB 3.5"/HH SCSI3 W/SC
D G V S - 3 9 1 1 0 ( 0 9 U ) IBM
Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders | | |
Capacity form/unform 9100/ MB Heads 12| | |
Seek time / track 6.3/ 0.7 ms Sector/track | | |
Controller SCSI3 WI/UL2/FA/SCA2 Precompensation
Cache/Buffer 1000 KB Landing Zone
Data transfer rate 16.000 MB/S int Bytes/Sector 512
40.000 MB/S ext SYNC
Recording method PRML,RLL 16/17 operating | non-operating
-------------+--------------
Supply voltage Temperature *C 5 50 | -40 65
Power: sleep W Humidity % 5 90 | 5 95
standby W Altitude km -0.300 3.000| -0.300 12.000
idle 16.5 W Shock g 10 | 140
seek W Rotation RPM 10020
read/write 19.3 W Acoustic dBA
spin-up W ECC Bit SMART
MTBF h
Warranty Month
Lift/Lock/Park YES Certificates
Layout
IBM DGVS-09 ULTRASTAR 9ZX
+-----------------------------------------------------+
| |
| |
| |
| |
|++---------SCSI-----------------+-Aux.---+-Power---++|
||| +------------------------1-+ |+-----1+|+-------+|||
||| |\::::::::::::::::::::::::/| ||::::::|||XXXXXXX||||
||| +------------------------35+ |+-----2+|+-------+|||
||+------------------------------+Connect.+-4-3-2-1-+||
++ ++
Jumpers
IBM DGVS-09U/09Y ULTRASTAR 9ZX
Jumper Setting
--------------
Termination
Power Enable
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ +--+--+
|01|03|05|07|xx|11|13|15|17|19|21|23|25|27|29|31| | | |
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ |01|02|
|02|04|06|08|10|12|14|16|18|20|22|24|26|28|30|32| | | |
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+ +--+--+
*NOTE: PINS 1 AND 2 DO NOT EXIST IN 50-PIN MODELS!
Pin| Description ---+--------------------------------------------------------- 01 | Bit 3 (MSB) (Do not exist in 50-pin models)--+ 03 | Bit 2 --+ Address 05 | Bit 1 --+ Jumpers 07 | Bit 0 (LSB) --+ 09 | Blank Polarity 10 | Unused 11 | Auto Start 13 | Ground 14 | Enable Active Termination 15 | -Master Sync 16 | -Slave Sync 17 | External Activity LED 18 | +5V 19 | Write Protect 21 | Auto Start Delay 23 | Option Block Mode 25 | Disable Sync Negotiations 27 | Disable SCSI Parity 29 | Disable Unit Attention 31 | Disable F/W Negotations
68/80-Pin SCSI ID ----------------- +----------+-------------------------------+ | SCSI ID | Jumper Location | | | PINS | | | Bit 3 | Bit 2 | Bit 1 | Bit 0 | +----------+-------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 1 | OPEN | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 2 | OPEN | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 3 | OPEN | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 4 | OPEN | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 5 | OPEN | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 6 | OPEN | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 7 | OPEN | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 8 | CLOSED| OPEN | OPEN | OPEN | +----------+-------+-------+-------+-------+ | 9 | CLOSED| OPEN | OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 10 | CLOSED| OPEN | CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 11 | CLOSED| OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+-------+ | 12 | CLOSED| CLOSED| OPEN | OPEN | +----------+-------+-------+-------+-------+ | 13 | CLOSED| CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+-------+ | 14 | CLOSED| CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+-------+ | 15 | CLOSED| CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+-------+
NOTE
For attachment to a Macintosh, place jumpers on pins 29 & 30 to
Disable Unit Attention and pins 11 & 12 for Auto Start.
Auto Start (& Delay) Pins
-------------------------
The Auto Start and Auto Start Delay pins control when and how the
drive can spin up and come ready. When configured for Auto-Startup,
the motor spins up after power is applied without the need of a SCSI
Start Unit command. For no Auto-Start, a SCSI Start Unit command is
required to make the drive spin and be ready for media access
operations. When in Auto-Start mode, the drive will delay it's start
time by a period of time multiplied by it's own SCSI address.
Write Protect Pins
------------------
If the Write Protect pin is jumpered to ground the drive will
prohibit SCSI commands that alter the customer data area portion of
the media from being performed. The state of this pin is monitored on
a per command basis.
Disable Sync. Negotiation Pins
-------------------------------
If a Disable Target Initiated Synchronous Negotiation pin is grounded
then an Initiator is required to start a negotiation handshake if
Synchronous and/or Wide (Double Byte) SCSI transfers are desired.
Disable SCSI Parity Pins
------------------------
Grounding this pin will disable SCSI Parity checking.
Disable Unit Attention Pins
---------------------------
Grounding this pin will disable the drive from building Unit
Attention Sense information for commands immediately following a
Power On Reset (POR) or SCSI Bus Reset. Any pending Unit Attention
conditions will also be cleared at POR or SCSI Reset times.
Install
-ANY DIREC.
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
Features
IBM DGVS-09U/Y ULTRASTAR 9ZX
Attaching the Drive
-------------------
1. Turn off the Computer, unplug the power cord and open the case.
2. The DGVS drive requires Active Termination on both ends of the
SCSI cable (the SCSI controller normally provides internal
termination for one end of the cable). If the DGVS drive is the
only device on the SCSI cable, attach it to the end of the cable
furthest from the controller and enable termination by placing a
jumper across pins 13 and 14 of the Option Jumper Block. If the
drive is attached to a cable that contains other devices and the
new drive is not attached to the end of the cable, the jumper
across pins 13 and 14 must be removed and Active Termination must
be supplied by the device at the end of the cable.
3. Select the other option jumpers as required by your computer.
4. Attach the power connector.
My Books
