Hard Drive: FUJITSU: MPA-3022AT 2260MB 3.5"/SL ATA3

M P A - 3 0 2 2 A T    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    8713|     |     |
Capacity form/unform  2260/      MB        Heads           3|     |     |
Seek time   / track  11.0/ 3.0 ms          Sector/track     |     |     |
Controller           IDE / ATA3            Precompensation
Cache/Buffer           128 KB              Landing Zone
Data transfer rate   10.000 MB/S int       Bytes/Sector      512
                     16.700 MB/S ext PIO4
Recording method     PRML 8/9                       operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep              W     Humidity     %         8 80    |      5 85
       standby            W     Altitude    km    -0.060  3.000| -0.060 12.000
       idle           3.8 W     Shock        g        10       |     75
       seek               W     Rotation   RPM      5400
       read/write     4.4 W     Acoustic   dBA        35
       spin-up            W     ECC        Bit   SMART
                                MTBF         h     500000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

FUJITSU MPA-30XXAT JUMPER SETTING

     +---------------------------------------+-------+--------+
     |* * * * * * * * * * * * * * * * * * * *| * * * |X X X X |
     |* * * * * * * * * *   * * * * * * * * *| * * * |        |
     +----IDE-Interface----------------------+-CN1---+-Power--+

Jumpers

FUJITSU MPA-30XX AT JUMPER SETTING

Jumper Setting
==============

     +---------------------------------------+-------+--------+
     |* * * * * * * * * * * * * * * * * * * *| * * * |X X X X |
     |* * * * * * * * * *   * * * * * * * * *| * * * |        |
     +----IDE-Interface----------------------+-CN1---+-Power--+

     ---------+-------+--------+
     * * * * *| xxx X |X X X X | Master Drive Setting (default)
       * * * *| * * X |        |
      --------+-CN1---+-Power--+

     ---------+-------+--------+
     * * * * *| xxx * |X X X X | Slave Drive Setting
       * * * *| * * xx|        |
      --------+-CN1---+-Power--+

     ---------+-------+--------+
     * * * * *| xxx * |X X X X | Cable Select Mode (CSEL)
       * * * *| * xxx |        |
      --------+-CN1---+-Power--+

Alternate Jumper Settings for Partitions Larger than 2.1 GB
===========================================================
On initial boot, the system BIOs may lock up on drives that have
more than 4098 cylinders (driver larger than 2.1 GB). Alternate
jumper setting have been provided for drives that are larger than
2.1GB to overcome this system BIOS limitation. These jumper settings
cause the drive to report 4092 cylinders (instead of the usual
4960,6296 or 7752) in Word 1 of the Identify Drive data.

     ---------+-------+--------+
     * * * * *| X * X |X X X X | Master Drive Setting (default)
       * * * *| X * X |        |
      --------+-CN1---+-Power--+

     ---------+-------+--------+
     * * * * *| X * xx|X X X X | Slave Drive
       * * * *| X * * |        |
      --------+-CN1---+-Power--+

     ---------+-------+--------+
     * * * * *| X * * |X X X X | Cables Select (CSEL)
       * * * *| X xxx |        |
      --------+-CN1---+-Power--+