Hard Drive: FUJITSU: M2243R 105MB 5.25"/HH RLL ST506
M 2 2 4 3 R FUJITSU
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/HH Cylinders 1186| | |
Capacity form/unform 105/ 130 MB Heads 7| | |
Seek time / track 25.0/ 5.0 ms Sector/track 26| | |
Controller RLL / ST506 Precompensation 576
Cache/Buffer KB Landing Zone 1185
Data transfer rate 0.938 MB/S int Bytes/Sector 512
0.938 MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 45 | -40 60
Power: sleep W Humidity % 20 80 | 5 95
standby W Altitude km 3.000| 12.000
idle W Shock g 2 | 20
seek W Rotation RPM 3600
read/write 18.0 W Acoustic dBA 45
spin-up W ECC Bit
MTBF h 30000
Warranty Month
Lift/Lock/Park YES Certificates
Layout
FUJITSU M2243T/R OEM MANUAL 41FH5014E-03
+---------------------------------------------------------+ | |XX B | |XX cable | 8-+ |XX edge | (Terminator)| | |XX 20-pin | SW2 | | |XX | 1-+ | | 1-+ |XX A | | | |XX cable | SW1 | | |XX edge | 8-+ |XX 34-pin | |XX | |XX | |XX | | | |XX | |XX Power | | +---------------------------------------------------------+
Jumpers
FUJITSU M2243T/R OEM MANUAL 41FH5014E-03
Jumper setting
==============
x = Jumpers are set at factory
Should not operate hatched short plug switches other than SW1 and
SW2.
SW1 Drive selection
--------------------
Drive Number 1 2 3 4
-------------------------------------------------
x 1 CLOSED OPEN OPEN OPEN
-------------------------------------------------
2 OPEN CLOSED OPEN OPEN
-------------------------------------------------
3 OPEN OPEN CLOSED OPEN
-------------------------------------------------
4 OPEN OPEN OPEN CLOSED
Plug 1 to 4 are used to select one of up to four drives. The relevant
plug is to be set "CLOSED" while the others should be set "OPEN".
SW1 Control of Drive Selected Signal
--------------------------------------
5 CLOSED A drive is in a selected state regardless of
Drive Select 1 to 4, which means Drive Selected
signal is always true and all Input/Output signals
are validated without selecting the drive.
x OPEN Drive Selected signal becomes true and all input/
output signals are validated only when a drive is
selected with Drive Select 1 to 4.
SW1 Control of Motor On signal
--------------------------------
6 OPEN
7 CLOSED By the Motor On signal
x 6 CLOSED
x 7 OPEN When the power-on
x 8 CLOSED Reserved
Plugs 6 and 7 are used to select the DC motor starting either by the
Motor On signal or not.
SW2 Terminating the Control Signals
-------------------------------------
This switch is used to terminate the control signals. Keys 1 to 8 in
SW2 of the last drive must be set to "ON" (in other drives, must be
set to "OFF").
x All keys are set to "ON".
Power supply connector
----------------------
1 = +12V
+------------+ 2 = +12V Return
| 4 3 2 1 | 3 = + 5V Return
+------------+ 4 = + 5V
Install
FUJITSU M2243T/R OEM MANUAL 41FH5014E-03
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
UNACCEPTABLE! UNACCEPTABLE!
Never install PC board on the Top!
The drive may be installed in its locker either vertically or
horizontally. The drive should not be positioned with the PCA on top.
Ambient temperature
-------------------
The operating termperature range of the drive is specified at a
distance of 3 cm from the drive.
Cable connection
----------------
The drive is interfaced to a system through four connectors.
Connection
----------
To connect two to four drives, the A cable (control signals) must be
connected in series and the B cable (R/W signals) in parallel. The
termination of control signals must be performed only at the last
drive.
+-------------+ +--------------+ | +-A-cable--*---+ Drive 1 +---------------------+ | +-B-cable--+---+ | | | | | +--------------+ | | | *---+ Drive 2 +-----------------+ | | +-B-cable--+---+ | | | | Controller | | +--------------+ | | | | *---+ Drive 3 | | | | +-B-cable--+---+ +------------+ | | | | | +--------------+ | | | | | +---X Drive 4 | | | | | +-B-cable------+ +--------+ | | | | | +--------------+ | | | | +-------------+ | | | | | +-------Power-cable--------------------+ | | | | | | | | | +-------Power-cable------------------------+ | | | Power supply| | | | +-------Power-cable-----------------------------+ | | | | | +-------Power-cable---------------------------------+ +-------------+
Frame structure
---------------
The disk enclosure (signal ground) is electrically isolated from the
drive mounting frame (frame ground). When mounting the drive in a
cabinet frame, the frame should clear the drive by at least 3.5 mm
to prevent the drive from touching the cabinet frame. An the locker
frame should clear the drive upper and lower side at least 2.5 mm.
In case of horizontally mount, do not mount the heating materials at
drive lower side.
Noise filter
------------
To eliminate AC line noise, a noise filter of the specifications
given below should be incorporated in the AC input terminal of the
disk drive power supply.
Attenuation characteristic: 40 dB or greater at 10MHz
Circuit configuration: T type
Features
FUJITSU M2243R/T OEM MANUAL 41FH5014E-03
Media error
-----------
Cylinder 0 is defect free.
The number of defect is 86 or less in the drive and the number of
defects per one head is 25 or less.
Mean Time Between Failures (MTBF)
---------------------------------
The MTBFs of the drive during their life time are 30,000 hours
estimated value after an initial period of 3-month.
Failure of the equipment means failure that requires either repairs,
adjustments, or replacement. Mishandling by the operator, failures
due to bad environmental conditions, power trouble, controller
trouble, cable failures, or other failures no caused by the equipment
are not included.
Mean Time To Repair
-------------------
MTTR is the average time taken by well-trained service mechanic to
diagnose and repair a drive malfunction. The drive is designed for a
MTTR of 30 minutes or less.
Service life
------------
Overhaul of the drive is not required for the first five years.
Preventive Maintenance
-----------------------
Preventive Maintenance is unnecessary.
Power loss
----------
Integrity of the data on the disk is guranteed against all froms of
abnormal DC power failure except a power failure during writing.
DC Power
--------
The direct-drive DC motor requires no adjustment for line frequencies
(50 Hz/60 Hz) or input power voltages (100, 115, 220 or 240 V).
Power consumption: Steady state 18 W.
Write Precompensation
---------------------
Whenever two bits are written in close proximity to each other, a
phenomenon called pulse superposition occurs, which tends to cause
the two bits to move away from each other. This is a factor
contributing to bit shift.
The effect of bit shift can be reduced by a technique called pre-
compensation, which, by detecting which bits will occur early and
which bits will occur late, can effectivly minimize the shift by
writing these bits in the opposite direction of the expected shift.
M2243T...Performance without writeprecompensation is guranteed.
M2243R...Precompensation had better done at 576 1185 cylinders. The
optimum amount of precompensation is 7 nanoseconds.
Spindle motor
-------------
The disks are turned by a direct-drive DC motor. The motor attains a
very precise rotational speed of 3600 rpm, 1%. This precision in
achieved through a feedback circuit which includes Hall-effect
elements mounted within the motor assembly.
Start and stop time
-------------------
Start time (time from when power is turned on until the unit is
ready) is 20 seconds or less and stop time (time to completely stop
when power is turned off) is 15 seconds or less using dynamic
braking.
My Books
