lotus

previous page: Hard Drive: CONNER: CP-30200 213MB 3.5"/SL    SCSI2 SE
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-3024 21MB 3.5"/SL    IDE / AT

Hard Drive: CONNER: CP-30204 212MB 3.5"/SL IDE / AT




C P - 3 0 2 0 4    CONNER
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/SLIMLINE         Cylinders    2119|  683|     |
Capacity form/unform   212/      MB        Heads           4|   16|     |
Seek time   / track  12.0/ 3.0 ms          Sector/track   49|   38|     |
Controller           IDE / AT              Precompensation
Cache/Buffer           256 KB SEGMENTED    Landing Zone
Data transfer rate    2.500 MB/S int       Bytes/Sector      512
                      8.000 MB/S ext
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |    -40 60
Power: sleep              W     Humidity     %         8 80    |      8 80
       standby            W     Altitude    km    -0.061  3.050|        12.192
       idle           5.2 W     Shock        g         5       |     75
       seek           6.6 W     Rotation   RPM      4498
       read/write     7.0 W     Acoustic   dBA        40
       spin-up            W     ECC        Bit   56,REED SOLOMON
                                MTBF         h     150000
                                Warranty Month        15
Lift/Lock/Park     YES          Certificates     CSA,FCC,IEC380,IEC950,TUV,...

Layout

CONNER CP30204 COUGAR PRODUCT MANUAL 00501-043 REV. B, APRIL, 1992

  +-------------------------------------------------------+
  | +-+                          SS++DSP                  |XX  J4
  | | |                   SPNSYNC +++                     |xx1 Power
  | | |HDA                                                |
  | | |                                                   |XX 40 Pin
  | +-+                                                   |XX Task
  |                                                       |XX File
  |                                                       |XX
  |                                                       |XX Inter-
  |                                                       |XX face
  |                                                       |XX
  | SPINSYNC                                              |XX J2
  | LED                                                   |XX
  |1--2                                                   |XX
  |+--+ J3      +-+-+-+-+                                 |
  ||  |         +-+-+-+-+                                 |XX Power J6
  |+--+        C/D E1 E2 E3                               |XX
  +-------------------------------------------------------+  1

Jumpers

CONNER CP30204 COUGAR PRODUCT MANUAL 00501-043 REV. B, APRIL 1992

Jumper Setting
==============

C/D Jumper
----------
Up to two drives may be daisy chained together utilizing the 40 pin
Task File connector. The maximum cable length is 18 inches. In order
to install more than one drive, it is necessary to set a jumper
option. The C/D jumper is used to determine whether the drive is a
master (drive C) or slave (drive D). The drive is configured as a
master (drive C) when jumpered and as a slave drive (D drive) when
not jumpered.

 DSP & SS Jumper
 ---------------
 This pair of jumpers determines the signal on pin 39 of the interface
 connector.
 +--------+------------------------------------------------------+
 | Jumper |         Action                                       |
 |DSP| SS |                                                      |
 +---+----+------------------------------------------------------+
 | X |    | - spindle synchronization signal disabled on pin 39. |
 |   |    | - activity LED signal available on pin 39            |
 +---+----+------------------------------------------------------+
 |   | X  | - spindle synchronization signal enabled on pin 39.  |
 |   |    | - activity LED signal disabled from pin 39           |
 +---+----+------------------------------------------------------+
 |   |    | - pin 39 floating                                    |
 +---+----+------------------------------------------------------+

Master/slave in ATA compatible mode uses pin 39 in a time multiplexed
manner to indicate that a slave drive is present. During power-on-
reset or after RESET is asserted, this line is asserted by the slave
drive within 400 ms to indicate its presence. The master drive allows
up to 450 msec for the drive to assert -HOST SLV/ACT. -HOST SLV/ACT
is deasserted by the slave drive following its acceptance of the
first valid command or after 31 seconds, whichever comes first.

 Jumpers E1, E2, E3
 ------------------
 E1 CLOSED  Jumper in disables spin-up at power-on. The drive will
            automatically spin up when it receives a command which
            accesses the drive.

E2 UNUSED

E3 UNUSED

Conner Master/Slave
-------------------
The drive is equipped with a -C/D jumper. To select the drive as the
master, in a two drive or ported system, or a single drive, the -C/D
jumper should be installed. If the jumper is not installed, the drive
will configure as the slave. The -PDIAG line is used as the slave
present signal to the master in the following way.

At power on time -PDIAG will be activated by the slave within 1 ms.
If the master does not see -PDIAG active after 4 ms it will assume no
slave is present. -PDIAG will remain active until the slave is ready
to go not busy or 14.0 seconds after a Power On Reset. The master
will wait 14.5 seconds or until the slave deactivates -PDIAG on
Power On Reset before it goes not busy. The slave will deactivate
-PDIAG and go not busy, if it is not ready after the 14.0 seconds.
Neither drive will set Ready or Seek Complete until they have reached
full spin speed and are ready to read and write.

During a software reset, -PDIAG will be activated by the slave within
1 millisecond. If the master does not see -PDIAG active after 4 ms it
will assume that no slave is present. The slave will not deactivate
-PDIAG until it is ready to go not busy or 400 ms. The master will
only wait 450 ms or until the slave deactivates -PDIAG before it goes
not busy. The slave will only wait 450 ms before it activates -PDIAG
and goes not busy. The drive will not set Ready or Seek Complete
until those states are achieved.

After Reset, -PDIAG is used in its normal diagnostic function during
the diagnostic command.

Install

CONNER CP30204 COUGAR PRODUCT MANUAL 00501-043 REV. B, APRIL 1992

Notes on installation
=====================

Screws
------
Side: 6-32 UNC 2B 5/32" Max. (6X)
6-32 UNC 2B 3/8" Max. (4X)

Power Connectors
----------------
The drive has two power connectors; a standard 4 pin DC power
connector and a smaller 3 pin connector. Power must only be supplied
at one source.

The mating connector for the four pin connector is AMP 1-480424-0
(Housing) and AMP 60619-4 (loose piece) or 61117-4 (strip) contacts.

  pin 1    +12 V
  pin 2    GND
  pin 3    GND
  pin 4    + 5 V

The mating connector for the three pin connector is Molex series
54-84 Header, housing Molex part number 39-01-0033 and terminal part
number 39-00-0031 (loose) or 39-00-0023 (strip).

  pin 1    + 5 V
  pin 2    +12 V
  pin 3    GND

Interface Connector
-------------------
The recommended mating connector is Molex P/N 15-47-3401 or
equivalent. Two drives may be daisy chained on this connector, and
the maximum cable length is 18 inches.

Magnetic Field
--------------
The disk drive will meet its specified performance while operating in
the presense of an externally produced magnetic field of 6 gauss DC
maximum.

Acoustic Noise
--------------
The sound pressure level will not exceed 40 dBA at a distance of 1
meter from the drive.

Signal Levels
-------------
All signal levels are TTL compatible. A logic 1 is > 2.0 Volts. A
logic 0 is from 0.00 Volts to 0.70 Volts.

 Signal Conventions
 ------------------
 All signals on the Host Interface shall have the prefix HOST. All
 active low signals shall be further prefixed with a "-" designation.
 All active high signals shall be prefixed with a "+" designation.
 Signals driven only by the Host will be indicated with an O, the
 signals driven by either the Host or the drive will be indicated with
 an I/O.

 +----+-------------------+----+----------------+
 | Pin|Signal             | Pin|Signal          |
 +----+-------------------+----+----------------+
 | 01 |-HOST RESET        | 02 |GND             |
 +----+-------------------+----+----------------+
 | 03 |+HOST DATA 7       | 04 |+HOST DATA 8    |
 +----+-------------------+----+----------------+
 | 05 |+HOST DATA 6       | 06 |+HOST DATA 9    |
 +----+-------------------+----+----------------+
 | 07 |+HOST DATA 5       | 08 |+HOST DATA 10   |
 +----+-------------------+----+----------------+
 | 09 |+HOST DATA 4       | 10 |+HOST DATA 11   |
 +----+-------------------+----+----------------+
 | 11 |+HOST DATA 3       | 12 |+HOST DATA 12   |
 +----+-------------------+----+----------------+
 | 13 |+HOST DATA 2       | 14 |+HOST DATA 13   |
 +----+-------------------+----+----------------+
 | 15 |+HOST DATA 1       | 16 |+HOST DATA 14   |
 +----+-------------------+----+----------------+
 | 17 |+HOST DATA 0       | 18 |+HOST DATA 15   |
 +----+-------------------+----+----------------+
 | 19 |GND                | 20 |KEY             |
 +----+-------------------+----+----------------+
 | 21 |RESERVED           | 22 |GND             |
 +----+-------------------+----+----------------+
 | 23 |-HOST IOW          | 24 |GND             |
 +----+-------------------+----+----------------+
 | 25 |-HOST IOR          | 26 |GND             |
 +----+-------------------+----+----------------+
 | 27 |RESERVED           | 28 |+HOST ALE       |
 +----+-------------------+----+----------------+
 | 29 |RESERVED           | 30 |GND             |
 +----+-------------------+----+----------------+
 | 31 |+HOST IRQ14        | 32 |-HOST IO16      |
 +----+-------------------+----+----------------+
 | 33 |+HOST ADDR 1       | 34 |-HOST PDIAG     |
 +----+-------------------+----+----------------+
 | 35 |+HOST ADDR 0       | 36 |+HOST ADDR2     |
 +----+-------------------+----+----------------+
 | 37 |-CS0               | 38 |-CS1            |
 +----+-------------------+----+----------------+
 | 39 |-HOST SLV/ACT      | 40 |GND             |
 +----+-------------------+----+----------------+

J3 Auxialiary Connector
-----------------------
The Auxiliary connector is used to provide optional signals at the
front of the drive. No connection should be made to the pins marked
RESERVED. These pins reserved for factory test purposes and improper
connection may adversely affect the drive.

 +----+----------------+----+----------------+
 | Pin|Signal          | Pin|Signal          |
 +----+----------------+----+----------------+
 | 01 |GND             | 02 |Syndle Sync     |
 +----+----------------+----+----------------+
 | 03 |+LED            | 04 |-LED            |
 +----+----------------+----+----------------+
 | 05 |KEY             | 06 |KEY             |
 +----+----------------+----+----------------+
 | 07 |RESERVED        | 08 |RESERVED        |
 +----+----------------+----+----------------+
 | 09 |RESERVED        | 10 |RESERVED        |
 +----+----------------+----+----------------+
 | 11 |RESERVED        | 12 |RESERVED        |
 +----+----------------+----+----------------+
 | 13 |RESERVED        | 14 |RESERVED        |
 +----+----------------+----+----------------+
 | 15 |RESERVED        | 16 |RESERVED        |
 +----+----------------+----+----------------+

 A drive select LED may be driven using two alternative pins on this
 drive. Pin 39 on the interface connector can be used to drive the LED
 with a current limited 5 volt supply if it is not configured for
 Spindle Synchronization. The 16-pin auxiliary connector (J3), pins 3
 and 4 provide an open collector drive signal and a current limiting
 resistor connected to +5V.

The spindle synchronization signal is also available on Pin 2 of J3.

Features

CONNER CP30204 COUGAR PRODUCT MANUAL 00501-043 REV. B, APRIL 1992

Key Features
------------
The CP30204 Cougar is a high performance 3.5 inch low-profile (1.0
inch high) 213 megabyte (formatted) disk drives with 12 ms average
seek time, that is designed to operate on an IBM PC/AT or equivalent
in translate mode. The drives feature fast 12 ms average seek time,
low 6.7 ms average rotational latency and high shock resistance.

Because the drive contains the Task File within its control logic, it
requires a simplified adapter board to operate. Conner Peripherals
has developed an adapter board to be used in conjunction with the
drive on an AT or equivalent system.

 - High performance rotary voice coil actuator with embedded servo
   system.

 - Auto translate feature, allowing operation as any drive type (not
   exceeding its capacity)

- 1,7 run length limited code

- High shock resistance

- Sealed HDA

- Automatic actuator latch against inner stop upon power-down.

 - Microprocessor-controlled diagnostics routines that are auto-
   matically executed at start-up

- Automatic error correction and retries

- 512 bytes block size

- Emulates IBM Task File and supports additional commands

- Up to two drives may be daisy-chained on the AT interface

- 256KB segmentable cache with LRU caching algorithm

- Redundancy on entire data path from data reception

- Single burst ECC on-the-fly

Seek Times
----------

       +----------------------------------+--------+
       |Track-to-Track         msec.      |        |
       |physical                          |   3    |
       |logical (translated)              |   7    |
       +----------------------------------+--------+
       |               Average msec. typ. |  12    |
       |               Average msec. max. |  30    |
       +----------------------------------+--------+
       |Latency                msec. avg. |   6.7  |
       +----------------------------------+--------+
       The timing is measured through the interface with the drive
       operating at nominal DC input voltages.

       The average seek time is determined by averaging the seek time
       for a minimum of 1000 seeks of random length over the surface
       of the disk.

Functional Description
----------------------
The drive contains all necessary mechanical and electronic parts to
interpret control signals, position the recording heads over the
desired track, read and write data, and provide a contaminant free
environment for the heads and disks.

Read/Write and Control Electronics
----------------------------------
One integrated circuit is mounted within the sealed enclosure in
close proximity to the read/write heads. Its function is to provide
head selection, read pre-amplification, and write drive circuitry.

The dual microprocessor-controlled circuit card provides the re-
maining electronic functions which include:

        - Read/Write Circuitry
        - Rotary Actuator Control
        - Interface Control
        - Spin Speed Control
        - Dynamic Braking

At power down the heads are automatically retracted to the inner
diameter of the disk and are latched and parked on a landing zone
that is off the data tracks at the inner diameter of the disk.

Drive Mechanism
---------------
A brushless DC direct drive motor rotates the spindle. The motor/
spindle assembly is dynamically balanced to provide minimal
mechanical runout to the disks. A dynamic brake is used to provide a
fast stop to the spindle motor and return the heads to the landing
zone when power is removed.

Air Filtration System
---------------------
The head-disk assembly is a sealed enclosure with an integral 0.3
micron filter which maintains a clean environment for the heads and
disks.

Head Positioning Mechanism
--------------------------
The read/write heads are supported by a mechanism coupled to the
voice coil actuator.

Read/Write Heads and Disks
--------------------------
Data is recorded on 95mm diameter disk through 3370 type heads.

Error Correction
----------------
The drive uses a Reed-Solomon code to perform error detection and
correction. The polynominal is able to detect a single burst of up to
51 bits in length or up to three bursts each of which may be up to 11
bits in length.

The error correction capability of the polynomial is a single error
burst with a maximum length of 22 bits or two independent error
bursts of up to 11 bits or less is corrected "on-the-fly" with no
performance degradation. The miscorrection probability using this
"on-the-fly" error correction is superior to the detection capability
of the traditionally used 56 bit computer generated code.

 Reliability and Maintenance
 ---------------------------
 MTBF                     150,000 hours (POH) based on comparison of
                          similar Conner products.
 MTTR                     10 minutes typical
 Preventive Maintenance   None
 Component Design Life    5 years

Safety Standard
---------------
Conner Peripherals disk drives are designed to comply with relevant
prodcut safety standards such as:

 - UL 478, 5th edition, Standard for Safety of Information Processing
   and Business Equipment, and UL 1950, Standard for Safety of
   Information Technology Equipment

 - CSA 22.2#154, Data Processing Equipment and CSA 22.2#220, Inform-
   ation Processing and Business Equipment CSA 22.2#950, Safety of
   Information Technology Equipment

 - IEC 435 Safety Requirements for Data Processing Equipment, IEC 380,
   Safety of Electrically Energized Office Machines, and IEC 950,
   Safety of Information Technology Equipment Including Electrical
   Business Equipment

 - TUV-VDE EN60950
       VDE 0805/5.9

- FCC Class B Part 15 Subpart J

Notice
------
Conner Peripherals makes no warranty of any kind with regard to this
material, including, but not limited to, the implied warranties of
merchantability and fitness for a particular purpose. Conner
Peripherals shall not be liable for errors contained herein or for
incidental consequential damages in connection with the furnishing,
performance, or use of this material.













TOP
previous page: Hard Drive: CONNER: CP-30200 213MB 3.5"/SL    SCSI2 SE
  
page up: Hard Drive Specs from CONNER
  
next page: Hard Drive: CONNER: CP-3024 21MB 3.5"/SL    IDE / AT