SIDE-4/ Hard Disk/Floppy Controller Settings and Configuration
ACCULOGIC, INC.
SIDE-4/ PLUS
Data bus: | 16-bit, ISA |
Size: | Half-length, full-height card |
Hard drives supported: | Two IDE(AT) drives |
Floppy drives supported: | Two 360KB, 720KB, 1.2MB or 1.44MB drives |
CONNECTIONS | |
Function | Location |
34-pin control cable connector-floppy drive | J1 |
4-pin connector-drive active LED | J2 |
40-pin AT Interface (IDE) connector | J3 |
9-pin serial port 2-internal | J4 |
15-pin game port-internal | J5 |
9-pin serial port 1-external | J6 |
25-pin parallel port-external | J7 |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
| » | I/O Channel Ready signal disabled | JP4 | open |
I/O Channel Ready signal enabled | JP4 | closed | |
| » | Floppy drive enabled | JP5 | pins 1 & 2 closed |
Floppy drive disabled | JP5 | pins 2 & 3 closed | |
| » | Floppy drive port address is 3F0-3F7h | JP6 | pins 1 & 2 closed |
Floppy drive port address is 370-377h | JP6 | pins 2 & 3 closed | |
| » | Single speed floppy drives supported | JP7 | pins 1 & 2 closed |
Dual speed floppy drives supported | JP7 | pins 2 & 3 closed | |
| » | Hard drive enabled | JP8 | pins 1 & 2 closed |
Hard drive disabled | JP8 | pins 2 & 3 closed | |
| » | IDE select mode enabled | JP9 | pins 1 & 2 closed |
Not used | JP9 | open | |
| » | Hard drive port address is 1F0-1F7h | JP10 | pins 1 & 2 closed |
Hard drive port address is 170-177h | JP10 | pins 2 & 3 closed | |
| » | Not used | JP11 | open |
| » | IRQ14 normal | JP12 | pins 1 & 2 closed |
IRQ14 delayed until ACTIVE- signal is removed | JP12 | pins 2 & 3 closed | |
SERIAL & PARALLEL PORT CONFIGURATIONS | |||
Function | Location | Setting | |
| » | Serial port 1 (CN6) enabled | JP13 | pins 1 & 2 closed |
Serial port 1 (CN6) disabled | JP13 | pins 2 & 3 closed | |
| » | Serial port 1 (CN6) set to COM1 | JP14 | pins 1 & 2 closed |
Serial port 1 (CN6) set to COM3 | JP14 | pins 2 & 3 closed | |
| » | Serial port 2 (CN4) enabled | JP15 | pins 1 & 2 closed |
Serial port 2 (CN4) disabled | JP15 | pins 2 & 3 closed | |
| » | Serial port 2 (CN4) set to COM2 | JP16 | pins 1 & 2 closed |
Serial port 2 (CN4) set to COM4 | JP16 | pins 2 & 3 closed | |
| » | Parallel port (CN7) enabled | JP17 | pins 1 & 2 closed |
Parallel port (CN7) disabled | JP17 | pins 2 & 3 closed | |
| » | Parallel port (CN7) address is LPT1 | JP18 | pins 1 & 2 closed |
Parallel port (CN7) address is LPT2 | JP18 | pins 2 & 3 closed | |
My Books
