TI-1210-8 (REV. D) video card Settings and Configuration

Category	Video
Video Types Supported	XVGA
Video Processor	Texas Instruments TMS34010
Highest Resolution Supported	1280 x 1024
Data Bus Type	16-bit ISA
Memory Type	Unidentified
Maximum Onboard Memory	Unidentified

CONNECTIONS
Purpose	Location	Purpose	Location
15-pin analog video port	CN1	VGA pass-through connector	CN2

BASE I/O ADDRESS SELECTION
Address	J3	J4	J5	J6	J7	J8	J9	J10
00000h	Closed	Closed	Closed	Closed	Closed	Closed	Closed	Closed
01000h	Closed	Closed	Closed	Closed	Closed	Closed	Closed	Open
02000h	Closed	Closed	Closed	Closed	Closed	Closed	Open	Closed
03000h	Closed	Closed	Closed	Closed	Closed	Closed	Open	Open
04000h	Closed	Closed	Closed	Closed	Closed	Open	Closed	Closed
FB000h	Open	Open	Open	Open	Open	Closed	Open	Open
FC000h	Open	Open	Open	Open	Open	Open	Closed	Closed
FD000h	Open	Open	Open	Open	Open	Open	Closed	Open
FE000h	Open	Open	Open	Open	Open	Open	Open	Closed
FF000h	Open	Open	Open	Open	Open	Open	Open	Open
Note: A total of 255 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. Jumper J3 is the Most Significant Bit and jumper J10 is the Least Significant Bit. The jumpers have the following decimal values: jumper J3=524288, J4=262144, J5=131072, J6=65536, J7=32768, J8=16384, J9=8192, J10=4096. Open the jumpers and add the values of the open jumpers to obtain the correct memory address. (open=1, closed=0)

EMULATION CONFIGURATION
Setting	J2
Enabled	Open
Disabled	Closed

VGA PASS-THROUGH CONFIGURATION
Setting	P1/Pins 5 & 6
Enabled	Closed
Disabled	Open

VGA PASS-THROUGH SYNC SIGNAL CONFIGURATION
Mode		J12
»	Composite sync	Pins 1 & 2 closed
	Horizontal sync	Pins 2 & 3 closed

SYNC SIGNAL CONFIGURATION
Mode		J15
»	Composite sync	Pins 2 & 3 closed
	Horizontal sync	Pins 1 & 2 closed

SYNC ON GREEN CONFIGURATION
Mode		J26
»	Composite sync	Pins 2 & 3 closed
	No sync on green	Pins 1 & 2 closed

TRANSFER WIDTH CONFIGURATION
Setting		J1
»	Disabled	Open
	Enabled	Closed

INTERRUPT SELECTION
IRQ		J22	J23	J24	J25
»	Disabled	Open	Open	Open	Open
	2/9	Open	Pins 1 & 2 closed	Open	Open
	6	Open	Pins 2 & 3 closed	Open	Open
	7	Pins 2 & 3 closed	Open	Open	Open
	10	Open	Open	Open	Pins 2 & 3 closed
	11	Open	Open	Open	Pins 1 & 2 closed
	12	Open	Open	Pins 1 & 2 closed	Open
	14	Pins 1 & 2 closed	Open	Open	Open
	15	Open	Open	Pins 2 & 3 closed	Open

DIRECT ACCESS ADDRESS SELECTION
Address	J16	J17	J18	J19	J20	J21
00000h	Closed	Closed	Closed	Closed	Closed	Closed
04000h	Closed	Closed	Closed	Closed	Closed	Open
08000h	Closed	Closed	Closed	Closed	Open	Closed
0C000h	Closed	Closed	Closed	Closed	Open	Open
10000h	Closed	Closed	Closed	Open	Closed	Closed
EC000h	Open	Open	Open	Closed	Open	Open
F0000h	Open	Open	Open	Open	Closed	Closed
F4000h	Open	Open	Open	Open	Closed	Open
F8000h	Open	Open	Open	Open	Open	Closed
FC000h	Open	Open	Open	Open	Open	Open
Note: A total of 63 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. Jumper J16 is the Most Significant Bit and jumper J21 is the Least Significant Bit. The jumpers have the following decimal values: jumper J16=524288, J17=262144, J18=131072, J19=65536, J20=32768, J21=16384. Open the jumpers and add the values of the open jumpers to obtain the correct memory address. (open=1, closed=0)

FACTORY CONFIGURED - DO NOT ALTER
Jumper	Position
JP1	Unidentified
JP2	Unidentified
Note: Exact location of jumpers unidentified.