IMASCAN CHROMA/PCI, IMASCAN MONO/MONO-D/PCI, IMASCAN RGB/RGB-D/PCI video card Settings and Configuration

Card Type	Video
Chip Set	Tseng Labs ET4000/W32
Maximum Onboard Memory	2MB DRAM
Data Bus	32-bit PCI
Video Types Supported	XVGA
Highest Resolution Supported	1280 x 1024

CONNECTIONS
Function	Label	Function	Label
VGA Out	J1	Capture video in	J4
VGA feature connector	J2	Daughter board connector	J5
Daughter board connector	J3
Note: The exact # of pins on J5 is unidentified.

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	IRQ 2/9 enabled	JP1	Pins 1 & 2 closed
	Any IRQ disabled	JP1	Pins 2 & 3 closed
»	Factory configured - do not alter	JP2	Unidentified
Note: JP2 sets the "Compliance Select" & does not appear on all board revisions.

CONNECTIONS
Function	Label	Function	Label
Daughter board connector	J1	Daughter board connector	J6
Note: The exact # of pins on J6 is unidentified.

CONNECTIONS
Function	Label	Function	Label
Daughter board connector	P1	Daughter board connector	P5
Digital port	P2
Note: The exact # of pins on P2 & P5 is unidentified.

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	Factory configured - do not alter	J1	Unidentified
»	Factory configured - do not alter	J2	Unidentified
»	Factory configured - do not alter	J3	Unidentified
»	Factory configured - do not alter	J4	Unidentified
»	Factory configured - do not alter	J5	Unidentified
»	Factory configured - do not alter	J6	Unidentified
»	Video1 75ohm termination enabled	J7	Pins 1 & 2 closed
	Video1 termination disabled	J7	Pins 2 & 3 closed
»	Video2 75ohm termination enabled	J8	Pins 1 & 2 closed
	Video2 termination disabled	J8	Pins 2 & 3 closed
»	Video3 75ohm termination enabled	J9	Pins 1 & 2 closed
	Video3 termination disabled	J9	Pins 2 & 3 closed
»	Video4 75ohm termination enabled	J10	Pins 1 & 2 closed
	Video4 termination disabled	J10	Pins 2 & 3 closed
»	Factory configured - do not alter	J11	Unidentified
»	Factory configured - do not alter	J12	Unidentified
Note: J1 - J3 sets the "Bus Select", J4 sets the "Field Invert", J5 & J6 sets the "Board Select", & J11 & J12 sets the "Termination".

USER CONFIGURABLE SETTINGS
Setting		Label	Position
»	Factory configured - do not alter	J1	Unidentified
»	Factory configured - do not alter	J2	Unidentified
»	Factory configured - do not alter	J3	Unidentified
»	Factory configured - do not alter	J4	Unidentified
»	Factory configured - do not alter	J5	Unidentified
»	Factory configured - do not alter	J6	Unidentified
»	Red1 75ohm termination enabled	J7	Pins 1 & 2 closed
	Red1 termination disabled	J7	Pins 2 & 3 closed
»	Green1 75ohm termination enabled	J8	Pins 1 & 2 closed
	Green1 termination disabled	J8	Pins 2 & 3 closed

USER CONFIGURABLE SETTINGS (CON’T)
Setting		Label	Position
»	Blue1 75ohm termination enabled	J9	Pins 1 & 2 closed
	Blue1 termination disabled	J9	Pins 2 & 3 closed
»	Red2 75ohm termination enabled	J10	Pins 1 & 2 closed
	Red2 termination disabled	J10	Pins 2 & 3 closed
»	Green2 75ohm termination enabled	J11	Pins 1 & 2 closed
	Green2 termination disabled	J11	Pins 2 & 3 closed
»	Blue2 75ohm termination enabled	J12	Pins 1 & 2 closed
	Blue2 termination disabled	J12	Pins 2 & 3 closed
Note: J1 - J3 sets the "Bus Select", J4 sets the "Field Invert", & J5 & J6 sets the "Board Select".