MULTI-TECH SYSTEMS, INC.
MULTIMOBILE (MT128NTZLX)
Card Type | ISDN |
Wiring Type | ISDN U-interface |
ISDN Transfer Rate | 64Kbps x 2 |
ISDN Protocol | ITU-T Q.921/Q.931, ETSI NET3 |
Data Bus | PCMCIA |
MULTI-TECH-SYSTEMS-INC-ISDN-MULTIMOBILE-MT128NTZLX
SUPPORTED COMMAND SET |
Basic AT Commands |
AT |
A, E |
&F, &V |
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
ASYNC TO SYNC LINK MODE | |
Type: | Configuration |
Format: | AT [cmds] &Nn [cmds] |
Description: | Selects Single-link or Multi-Link mode for Async to Sync PPP conversion |
Command | Jack Type |
&N0=0 | Single-Link mode for Async to Sync PPP conversion |
&N0=1 | Multi-Link mode for Async to Sync PPP conversion |
DIAL | |
Type: | Immediate |
Format: | AT [cmds] D<#> [cmds] |
Description: | Dials ISDN telephone number according to any modifiers included in the string |
Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command | Function |
DSn | Dial stored telephone number n |
DT | Dial out ISDN number |
DL | Redial last ISDN number |
HARDWARE VERIFICATION | |
Type: | Immediate |
Format: | AT [cmds] &Kn [cmds] |
Description: | Verifies TA hardware function. Reports "OK" or "BAD" |
ISDN LINK | |
Type: | Configuration |
Format: | AT [cmds] Hn [cmds] |
Description: | Selects various options for ISDN link |
Command | Function |
H0 | Hang up ISDN link |
H4 | Restart ISDN layer 2 link. Command issued when SPID number have changed |
H5 | View ISDN TA status responses |
LOAD PROFILE | |
Type: | Configuration |
Format: | AT [cmds] &Ln [cmds] |
Description: | Loads user profile into active RAM |
Command | Function |
&L0 | Load user profile 0 to active RAM |
&L1 | Load user profile 1 to active RAM |
&L2 | Load user profile 2 to active RAM |
&L3 | Load user profile 3 to active RAM |
&L4 | Load user profile 4 to active RAM |
&L5 | Load user profile 5 to active RAM |
&L6 | Load user profile 6 to active RAM |
&L7 | Load user profile 7 to active RAM |
&L8 | Load user profile 8 to active RAM |
&L9 | Load user profile 9 to active RAM |
MULTI-LINK | |
Type: | Configuration |
Format: | AT [cmds] &Jn [cmds] |
Description: | Selects whether one or two ISDN phone numbers are used for Multi-Link PPP connections |
Command | Jack Type |
&J0 | Two different phone numbers are use for Multi-Link PPP connection |
&J1 | Single ISDN phone number is used for Multi-Link PPP connections |
ON-LINE | |
Type: | Immediate |
Format: | AT [cmds] On [cmds] |
Description: | Controls on-line command (data transmission) state options. |
Command | Function |
O0 | On-line command mode enabled |
POWER-UP PROFILE | |
Type: | Configuration |
Format: | AT [cmds] &Pn [cmds] |
Description: | Copies selected profile into profile E and sets it as power-up profile |
Command | Function |
&P0 | Copy user profile 0 to user profile E, and set it as power-up profile |
&P1 | Copy user profile 1 to user profile E, and set it as power-up profile |
&P2 | Copy user profile 2 to user profile E, and set it as power-up profile |
&P3 | Copy user profile 3 to user profile E, and set it as power-up profile |
&P4 | Copy user profile 4 to user profile E, and set it as power-up profile |
&P5 | Copy user profile 5 to user profile E, and set it as power-up profile |
&P6 | Copy user profile 6 to user profile E, and set it as power-up profile |
&P7 | Copy user profile 7 to user profile E, and set it as power-up profile |
&P8 | Copy user profile 8 to user profile E, and set it as power-up profile |
STORE ACTIVE PROFILE | |
Type: | Configuration |
Format: | AT [cmds] &Wn [cmds] |
Description: | Writes the values for the active profile into RAM |
Command | Function |
&W0 | Write the active profile to stored profile 0 |
&W1 | Write the active profile to stored profile 1 |
&W2 | Write the active profile to stored profile 2 |
&W3 | Write the active profile to stored profile 3 |
&W4 | Write the active profile to stored profile 4 |
&W5 | Write the active profile to stored profile 5 |
&W6 | Write the active profile to stored profile 6 |
&W7 | Write the active profile to stored profile 7 |
&W8 | Write the active profile to stored profile 8 |
&W9 | Write the active profile to stored profile E |
SECONDARY DIAL NUMBER | |
Type: | Configuration |
Format: | AT [cmds] &Zn [cmds] |
Description: | Sets the secondary dial number for Async to Sync Multi-Link PPP mode |
STORE TELEPHONE NUMBER | |
Type: | Configuration |
Format: | AT [cmds] &Zn=x |
Description: | Writes selected saved telephone numbers into the non-volatile memory at location n |
Extended AT Command Set
BEARER CHANNEL PROTOCOL | |
Type: | Configuration |
Format: | AT [cmds] !Z=n |
Description: | Select bearer channel protocol |
Command | Function |
n =05 | V.120 |
n=09 | Asynchronous to synchronous PPP conversion |
BEARER CHANNEL SPEED | |
Type: | Configuration |
Format: | AT [cmds] !Q=n |
Description: | Sets B-channel speed |
Command | Function |
n =0 | Sets B-channel speed to 64Kbps |
n=4 | Sets B-channel speed to 56Kbps |
ISDN D-CHANNEL PROTOCOL | ||
Type: | Configuration | |
Format: | AT [cmds] !Cn=x(SPID #) | |
Description: | Sets service profile ID and switches selection | |
Note: | SPID numbers can include up to 20 characters. | |
Command | Function | |
C0=00 | Sets ISDN D-channel protocol (AT&T 5ESS custom) | |
C0=01 | Sets ISDN D-channel protocol (Northern Telecom DMS-100 custom) | |
C0=02 | Sets ISDN D-channel protocol (ETSI Europe ISDN) | |
í C0=05 | Sets ISDN D-channel protocol (US national ISDN-1) | |
C2 | Sets service profile ID 1 | |
C6 | Sets service profile ID 0 |
ISDN DIRECTORY NUMBER | |
Type: | Configuration |
Format: | AT [cmds] !Nn=x(ISDN phone #) |
Description: | Sets ISDN directory number |
Command | Function |
!N0 | Sets directory number 0 (DN 0) |
!N1 | Sets directory number 1 (DN 1) |