Hard Drive: SINGAPORE: 3387 NS 8700MB 3.5"/HH SCSI3 ULTR

3 3 8 7   N S    SINGAPORE
                                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    4811|     |     |
Capacity form/unform  8700/      MB        Heads            |     |     |
Seek time   / track   7.9/ 1.0 ms          Sector/track     |     |     |
Controller           SCSI3 SI/ULTRA        Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate          MB/S int       Bytes/Sector      512
                     20.000 MB/S ext SYNC
Recording method                                    operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 55    |
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle          14.0 W     Shock        g                 |
       seek          17.0 W     Rotation   RPM      7200
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h     650000
                                Warranty Month
Lift/Lock/Park     YES          Certificates                                  

Layout

MICROPL. 3387/4341 NS JUMPER SETTING

   +---------------------------------------------------------------+
   |                                                               |
   | REAR VIEW                                                     |
   |                                                               |
   |+----------------------------------------------------POWER----+|
   ||+-------------------------------------------------+-------1-+||
   |||o o o o o o o o o o o o o o o o o o o o o o o o 1| X X X X |||
   |||o o o o o o o o o o o o o o o o o o o o o o o o o| X X X X |||
   ||+--------------SIGNAL-CONNECTOR-------------------+---------+||
   ++                                                   +5V     +12V

   +------OPTION-JUMPER---------------------------------------------+
   |    +-------------------1+                +-TEST-------+        |
   |    |:::::  ::  :::::::::|           LED+ | :::::::::: |        |
   +----+--------------------+-------------++-+-FACTORY----+--------+
   |                                                                |
   |                                                                |
   +----------------------------------------------------------------+

Jumpers

MICROPL. 3387/4341 NS JUMPER SETTING

Jumper Setting
==============

* = Default

Drive Option Selection
----------------------

                                    +------------------- SP1
                                    |        +---------- ID2
                                    |        |  +------- ID1
                                    |        |  |  +---- ID0
     W3 W2 W1 W4  KEY      KEY      |        |  |  |  +- Remote LED+
 +--+-++-++-++-++-++--+--+-++--+--+-++--+--+-++-++-++-++
 |35|33|31|29|27|25|23|21|19|17|15|13|11|09|07|05|03|01|
 +--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
 |36|34|32|30|28|26|24|22|20|18|16|14|12|10|08|06|04|02|
 +-++--+--+--+--+--+-++-++--+-++-++--+-++-++--+--+--+-++
   |                 |  |     |  WP    |  |           +- Remote LED-
   |                 |  |     PTY      |  |
   |                 |  |              |  +------------- RESERVED
   |                 |  |              +---------------- SP0
   +-----------------+--+-------------------------------RESERVED

NOTE
Pin 4, 6, 8, 10, 12, 14, 16, 18, 22, and 24 are tied to Ground.

Option Jumper Block J2 is a 36-pin connector used for drive
addressing and various configuration options.

Test Connector is for factory use only - no jumper connections
allowed.

Single-Ended Configuration Options
----------------------------------

 SCSI ID
 -------
   +----------+-----------------------+ Up to eight devices (the host
   | SCSI ID  |        Jumpers        | and seven targets) can be
   |          | ID2   | ID1   | ID0   | attached to the SCSI Bus.
   +----------+-------+-------+-------+
   |    0     | OPEN  | OPEN  | OPEN  | ID jumpers ID0, ID1 and ID2
   |    1     | OPEN  | OPEN  | CLOSED| are used to assign one of
   |    2     | OPEN  | CLOSED| OPEN  | eight SCSI ID bits (0-7) to
   |    3     | OPEN  | CLOSED| CLOSED| the drive.
   |    4     | CLOSED| OPEN  | OPEN  |
   |    5     | CLOSED| OPEN  | CLOSED| In multiple-device systems,
   |    6     | CLOSED| CLOSED| OPEN  | each drive must have its own
   | *  7     | CLOSED| CLOSED| CLOSED| unique ID.
   +----------+-------+-------+-------+

 SP0/SP1  Spindle Control Option
 -------------------------------
    SP0 CLOSED
    SP1 OPEN   Spindle motor starts when START UNIT command is
               received.

    SP0 OPEN   (default)
    SP1 OPEN   Spindle motor starts at power-on.

 SP0/SP1  Spindle Delay Option
 -----------------------------
    SP1 CLOSED
    SP0 OPEN   Spindle start-up is delayed based on SCSI ID (12
               seconds per ID).

    SP1 OPEN   (default)
    SP0 OPEN   Spindle motor starts at power on.

 WP  Write Protect Option
 ------------------------
    WP CLOSED  Drive is write protected.
    WP OPEN    Drive is not write protected. (default)

 PTY  Bus Parity Check Option
 ----------------------------
    PTY CLOSED  Drive neither generates nor detects parity.
        OPEN    Drive generates parity and has parity detection
                enabled. (default)

W1/W2/W3 Bus Termination Power Option
--------------------------------------

 W1  CLOSED (default)
     Drive provides terminator power.

 W2  CLOSED
     Host system provides terminator power (via J1).

 W3  CLOSED
     Drive provides terminator power (via J1) to the SCSI BUS.

 W4 Interface Termination
 ------------------------
   W4 *INSTALLED  Drive provides termination for the interface lines,
                  i.e., onboard termination is electrically enabled.

       OMITTED    Drive does not provide termination for the interface
                  lines; i.e., onboard termination is electrically
                  disabled.

Remote LED
----------
Open-collector output - Used to drive a user-supplied LED to indicate
the drive is active.