lotus

previous page: Hard Drive: MAXTOR: LXT-200A 207MB 3.5"/HH    IDE / AT
  
page up: Hard Drive Specs from MAXTOR
  
next page: Hard Drive: MAXTOR: LXT-213A 213MB 3.5"/HH    IDE / AT

Hard Drive: MAXTOR: LXT-200S 201MB 3.5"/HH SCSI1 SE




L X T - 2 0 0 S    MAXTOR
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    1320|     |     |
Capacity form/unform   201/  234 MB        Heads           7|     |     |
Seek time   / track  15.0/ 3.0 ms          Sector/track     |     |     |
Controller           SCSI1 SINGLE-ENDED    Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    1.000 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL 1/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C                 |
Power: sleep              W     Humidity     %                 |
       standby            W     Altitude    km                 |
       idle               W     Shock        g                 |
       seek               W     Rotation   RPM
       read/write         W     Acoustic   dBA
       spin-up            W     ECC        Bit
                                MTBF         h     150000
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

MAXTOR LXT-200S

 +---+------------------------------------------------------------+
 |   |                                                            |
 |J3 |   JP6   xx JP8                                             |
 |   | +-----+                                                    |
 +--++ |||||:|<---------+                                     +-+ |
 +--++ +-----+          |    +--------------------+           | | |
 |   | ++.              |    |    9  7  5  3  1   |        J5 | | |
 |   | ||               |    | +----------------+ |           | | |
 |   | ||               |    | |  X  X  X  X  . | |           +-+ |
 |   | ++               +--->| +----------------+ |           +-+ |
 |   | ++.                   |   10  8  6  4  2   |           | | |
 |   | ||                    +--------------------+        J2 | | |
 |J1 | ||                                                     | | |
 |   | ++                                                     | | |
 |   | ++.                                                    +-+ |
 |   | ||                                                     +-+ |
 |   | ||                                                  J4 | | |
 |   | ++                   LXT-XXXS PCB Layout               +-+ |
 +---+------------------------------------------------------------+

Jumpers

MAXTOR LXT-200S

 Jumper Setting
 ==============
                   JP6
                   ----

            Pins  *9-10 = Motor Start
                  *7-8  = Parity   In = Enabled   Out = Disabled
                  *5-6  = SCSI ID MSB
                  *3-4  = SCSI ID
                   1-2  = SCSI ID LSB

       *JP8 = Terminator Power

       SCSI     Pins     Pins     Pins
        ID      5 & 6    3 & 4    1 & 2
       ----     -----    -----    ------             * NOTE *
        0        O         O        O
        1        O         O        J                O = Open
        2        O         J        O                J = Jumped
        3        O         J        J
        4        J         O        O             * = Factory Default
        5        J         O        J                 Jumped
        6        J         J        O
        7        J         J        J

General

MAXTOR SCSI INSTALLATION

         GENERIC INSTALLATION PROCEDURE FOR A SCSI DRIVE
   -----------------------------------------------------------

 1. Install a 50 pin ribbon connector making sure pin 1, which
    can be identified by the striped edge of the cable, is closest
    to the power connector on the drive.

2. Install a DC power cable to the back of the drive.

 3. Verify the SCSI ID selection.
    Note: SCSI ID usually needs to be set to 0 to be the boot drive.
    The last physical device on the SCSI bus must be terminated.
    Any other drive or SCSI device connected between the host and
    the device at the end of the bus must not be terminated.

4. Apply power to the computer.

  4a. When memory test is complete go into your system's Standard
      C-MOS set-up.
      (Note:  There are various ways to get into C-MOS set-up,
      please refer to system's manual for instuctions.)

  4b. Set the drive type to "Not Installed". This intelligent drive
      will identify itself to the SCSI host adapter.

 5. Boot from a DOS diskette that has FDISK.EXE and FORMAT.COM on
    it. At the A> prompt type in FDISK. At the menu options select
    option 1 to create a DOS partition. Another menu will appear and
    from those options choose 1 to create a Primary DOS partition.
    Select yes to make 1 large partition and it will automatically
    become active. Then escape from FDISK.

 6. At the A> prompt type in FORMAT C:/S
    This does a high-level format on the drive and transfers the
    system files in order for the drive to be bootable.
    (Note: Maxtor SCSI drives are low-level formatted at the factory)

 7. The drive is now bootable. As a test remove the DOS diskette
    from A and press reset to re-boot the computer, a C> should be
    displayed, the drive is now ready for operation.













TOP
previous page: Hard Drive: MAXTOR: LXT-200A 207MB 3.5"/HH    IDE / AT
  
page up: Hard Drive Specs from MAXTOR
  
next page: Hard Drive: MAXTOR: LXT-213A 213MB 3.5"/HH    IDE / AT