lotus

previous page: Hard Drive: FUJITSU: M2724TAM 1632MB 2.5"/SSL   ATA3
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M2903QAM 2100MB 3.5"/HH    SCSI2 WIDE

Hard Drive: FUJITSU: M2903HA 2130MB 3.5"/HH SCSI2 DIFF




M 2 9 0 3 H A    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 3.5"/HH               Cylinders    3150|     |     |
Capacity form/unform  2130/      MB        Heads          13|     |     |
Seek time   / track  10.0/ 2.0 ms          Sector/track     |     |     |
Controller           SCSI2 DI/FAST         Precompensation
Cache/Buffer           512 KB READ-AHEAD   Landing Zone
Data transfer rate    4.700 MB/S int       Bytes/Sector      512
                     10.000 MB/S ext SYNC
Recording method     RLL 8/9                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 50    |    -40 60
Power: sleep              W     Humidity     %        20 80    |      5 95
       standby            W     Altitude    km    -0.300  3.000| -0.300 12.000
       idle               W     Shock        g         5       |     50
       seek               W     Rotation   RPM      5400
       read/write         W     Acoustic   dBA        43
       spin-up            W     ECC        Bit
                                MTBF         h     500000
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

FUJITSU M2909H/2903H/2915H JUMPER SETTING

  +------------------------------++-------------------------+
  |                          +--++++                D **CN6 |XXI
  |                          |  +CN9                P **    |XXN
  |   +----------+           |  +  |                A **    |XXT
  |   |          |           |  +  |      CN7+-+SY          |XXE
  |   |          |           |  +  |         | |R           |XXR
  |   |          |          CN25+  |         | |WP          |XXF
  |   |          |           |  +  |         +-+TM          |XXA
  |   +----------+           +--+-++                        |XXC
  |                           +--++-+     CN4+-+ID0         |XXE
  |                           |  +CN8        | |ID1         |XX
  |                           |  +  |        +-+ID2         |XX
  |  +-+CN20                  |  +  |                       |XX
  |  +-+                     CN24+  |                       |XX
  |                           |  +  |                       |
  |                           |  +  |                       |XX Power
  |                           +--+-++                       |XX
  +--------------------------------++-----------------------+

Jumpers

FUJITSU M2903HA/M2909HA JUMPER SETTING

Jumper Setting
==============

* = Factory default

 Terminal Connector CN4 SCSI ID
 ------------------------------
  +------+------+------+--------+
  |ID2   |ID1   |ID0   |SCSI ID |
  +------+------+------+--------+
  |OPEN  |OPEN  |OPEN  |  0     |
  +------+------+------+--------+
  |OPEN  |OPEN  |SHORT |  1     |
  +------+------+------+--------+
  |OPEN  |SHORT |OPEN  |  2     |
  +------+------+------+--------+
  |OPEN  |SHORT |SHORT |  3     |
  +------+------+------+--------+
  |SHORT |OPEN  |OPEN  |  4     |
  +------+------+------+--------+
  |SHORT |OPEN  |SHORT |  5     |
  +------+------+------+--------+
  |SHORT |SHORT |OPEN  |  6     |
  +------+------+------+--------+
  |SHORT*|SHORT*|SHORT*|  7     |
  +------+------+------+--------+

 Terminal Connector CN6
 ----------------------
 Spindle motor control
   A    SHORT*  Auto Start on power up
        OPEN    Controlled by START/STOP UNIT command

 SCSI Bus Parity checking
   P   SHORT* Enabled
       OPEN   Disabled

 Offline Self-diagnostics
   D   SHORT*  Normal
       OPEN    Execute

 Terminal Connector CN7
 ----------------------
 Spindle Sync I/O pulse. Master & Slave control determining whether to
 receive or transmit SPSYNC are set by MODE SELECT command. This
 terminal
  SY  Pin 1 GROUND
      Pin 2     SPSYNC

External Reset. This would normally be connected to a momentary
switch which would short pin 3 to ground for the reset of the drive
and SCSI bus. Normally used for debug purposes only.

  R   SHORT* External reset signal when connected to ground
      OPEN   No connection

 Write protection
  WP  SHORT* Disabled
      OPEN   Enabled

 Termination of SCSI bus
  TM  SHORT* Enable terminating resistor
      OPEN   Disable terminating resistor

Terminal Connector CN20 External LED connector
----------------------------------------------
Pin 1 LED(V)
Pin 2 -LED

====================================================================

 Terminal Connector CN6
 ----------------------
 +6-4-2+
 |* * *|
 |* * *| CN6
 +5-3-1+
  D P A

 Spindle motor control
   A    SHORT*  Auto Start on power up
        OPEN    Controlled by START/STOP UNIT command

Set how to control the starting HDD spindle motor. This setting only
determines the operation mode when the power supply is turned on or
the microcode is downloaded.

In both modes, stopping or restating the spindle motor can be
controlled by specifying the START/STOP UNIT command.

 SCSI Bus Parity checking
 ------------------------
   P   SHORT* Enabled
       OPEN   Disabled

 Offline Self-diagnostics
 ------------------------
   D   SHORT*  Diagnostic Mode
       OPEN    Normal Operation

Setting terminals CN5-6 are used to set starting/stopping the HDD
self-diagnostics. The offline self-diagnostics can test the normality
of the HDD controller function and the basic read/write operation,
the setting terminals must be open.

 Terminal Connector CN7
 ----------------------
 Spindle Sync I/O pulse. Master & Slave control determining whether to
 receive or transmit SPSYNC are set by MODE SELECT command. This
 terminal
  SY  Pin 1 GROUND
      Pin 2 SPSYNC

External Reset. This would normally be connected to a momentary
switch which would short pin 3 to ground for the reset of the drive
and SCSI bus. Normally used for debug purposes only.

  R   SHORT* External reset signal when connected to ground
      OPEN   No connection

 CN7 Pins 5-6 Write protection
 -----------------------------
  WP  SHORT  Write operation is disabled
      OPEN*  Write operation is enabled

 CN7 Pins7-8 Termination of SCSI bus (Single-Ended type, 8-bit)
 --------------------------------------------------------------
  TM  SHORT* Enable terminating resistor
      OPEN   Disable terminating resistor

Setting terminal CN7 7-8 set whether to use the terminating resistor
circuit on the SCSI interface provided for the HDD. The setting
terminals enable the terminating resistor circuit to be connected on
the SCSI interface. Only the HDD of the single-ended type is
provided with the terminating resistor circuit.

 CN7 Pins7-8 Termination of SCSI bus (Differential type, 16-bit)
 ---------------------------------------------------------------
 7-8  SHORT* 16-bit SCSI mode setting
      OPEN   8-bit SCSI mode setting

Set setting terminal CN7 7-8 enable or disable the 16-bit SCSI mode.
When the 16-bit SCSI mode is enabled, all data bus (DB00 to DB15,
DBP0 to DBP1) can be effective. When the Differential type 16-bit
SCSI HDD is used as 8-bit SCSI device, this setting must be open.

Terminal Connector CN20 External LED connector
----------------------------------------------
Pin 1 LED(V)
Pin 2 -LED

 CN10 Single-Ended 16-bit
 ------------------------
  +4-2+
  |* *|
  |* *| CN10
  +3-1+

Setting terminals CN10 1-2 and 3-4 set whether to use the terminating
resistor circuit on the SCSI interface provided for the HDD.
The setting terminals enable the terminating resistor circuit to be
connected on the SCSI interface.

CAUTION
This setting is effective when the external operator panel (S6) is
connected and pin A9 (TERM-ON) is open.

 +-------+-------+---------------------------------------------------+
 |Pins   | Pins  |Connection of the terminating resistor on the SCSI |
 |1-2    | 3-4   |Interface                                          |
 +-------+-------+---------------------------------------------------+
 |OPEN   | OPEN  |Terminating resistor circuit is not connected      |
 +-------+-------+---------------------------------------------------+
 |CLOSED | CLOSED|Terminating resistor circuit is connected          |
 +-------+-------+---------------------------------------------------+

 CN10 Setting connecting of terminating resistor on SCSI interface
 -----------------------------------------------------------------
 (Single-ended type 16-bit SCSI is used as 8-bit SCSI)
 +-------+-------+---------------------------------------------------+
 |Pins   | Pins  |Connection of the terminating resistor on the SCSI |
 |1-2    | 3-4   |Interface                                          |
 +-------+-------+---------------------------------------------------+
 |OPEN   | CLOSED|Terminating resistor circuit is not connected      |
 +-------+-------+---------------------------------------------------+
 |CLOSED | CLOSED|Terminating resistor circuit is connected          |
 +-------+-------+---------------------------------------------------+

Install

FUJITSU M2903/M2909/M2915 JUMPER SETTING

Notes On Installation
=====================

Installation direction
----------------------

     horizontally                           vertically
   +-----------------+             +--+                       +--+
   |                 |             |  +-----+           +-----+  |
   |                 |             |  |     |           |     |  |
 +-+-----------------+-+           |  |     |           |     |  |
 +---------------------+           |  |     |           |     |  |
                                   |  |     |           |     |  |
                                   |  |     |           |     |  |
 +---------------------+           |  +-----+           +-----+  |
 +-+-----------------+-+           +--+                       +--+
   |                 |
   |                 |
   +-----------------+

The drive will operate in all axis (6 directions).

Installation direction
----------------------
The drive may be installed in one of 6 orientations, that is on any
of its facets. Inclination from vertical should be less than 5*.

Mounting screws
---------------
Either side or underside mounting may be used. Standard drive use M3
screws but some special models and US versions use 6/32 UNC. Screws
should not protrude from the drive frame by more than 3mm or damage
may occur. Mounting Screws: M3 x 5mm#6/32 UNC, M3 x 5mm#6/32 UNC

Frame clearance
---------------
There should be a gap of at least 2.5mm between the drive and the
system mounting frame on all sides to provide for adequate air flow.

Grounding
---------
The M29xx series drives use Magneto-Resistive (MR) heads and
therefore require special handling considerations. Users must ensure
that the DE casing is NEVER shorted to the computer system's Frame or
DC Ground.

 Recommended Parts For Connection
 --------------------------------
 Part                         | Manufacturer  | Part Number
 -----------------------------+---------------+-----------------
 SCSI Connector (closed end)  | Fujitsu Ltd.  | FCN-707B050-AU/B
 -----------------------------+---------------+-----------------
 SCSI Connector (through-end) | Fujitsu Ltd.  | FCN-707B050-AU/O
 -----------------------------+---------------+-----------------
 Power Connector(housing)     |               | AMP 1-480424-0
 -----------------------------+---------------+-----------------
 (contact for wire AWG 18 24) |               | AMP 170121-4
 -----------------------------+---------------+-----------------
 DC Grounding (faston)        |               | AMP 62187-1
 -----------------------------+---------------+-----------------
 External LED (housing)       | ELCO          | 608283302815000
 -----------------------------+---------------+-----------------
 (contact for wire AWG 24 30) | ELCO          | 608283052330808
 -----------------------------+---------------+-----------------

Features

FUJITSU M2909/M2903/M2915 JUMPER SETTING

General
-------
Fujitsu introduces a revolutionary technology for manufacturing
high-capacity, low profile, fast access disk drives. Fujitsu's latest
technology, the MR (Magneto-resistive) head technology, has made it
possible to store 3.1 gigabytes on the M2909 as well as 2.1 gigabytes
on the M2903 and M2915.

Advanced Technologies
---------------------
The adoption of the MR head, PR4ML (Partial Response class 4 Maximum
Likelihood) and 8,9 encoding/decoding enables the storage of much
more data than was previously possible. MR technology employs
separate read/write transducers, which allows MR drives to store
nearly 300 megabits per square inch. PR4ML increases drive
performance by allowing more data to be recorded on each track and
sustained reads at 6.8 megabytes per second for the M2903 and M2909,
and 8.7 megabytes per second for the M2915. 8,9 encoding/decoding
code results in improved signal strength. Together, these
technologies realise recording densities as high as 75,535 bpi for
the M2903 and M2909, and 71,627 bpi for the M2915. Track density is
also as high as 3,553 tpi, leading to large storage capacity, and
with advanced "On the fly ECC" error correction technology, makes the
M2903, M2909 and M2915 ideal for workstations, servers, disk arrays,
minicomputers and mainframes.

Rapid Rotational Speed
----------------------
The 3 gigabytes storage capacity model M2909 and the 2 gigabytes
storage capacity model M2903 and the 2 gigabytes storage capacity
model M2903 achieve a rapid rotational speed of 5,400 rpm and
provides a fast positioning time of 2.0 milliseconds track-to-track,
10.5 milliseconds average and 22 milliseconds maximum, including
settling time.

As for 2 gigabytes storage capacity range, Fujitsu provides the
performance-focused model M2915 in addition to the M2903. The M2915
achieves a more rapid rotational speed of 7,200 rpm and provides a
fast positioning time of 2.0 milliseconds track-to-track, 9.8
milliseconds average and 21 milliseconds maximum, including settling
time. The M2915 is especially suitable for client server,
video-on-demand and transaction-processing applications.

Various Models with SCSI-2 I/F
------------------------------
The M2903, M2909 and M2915 provide both fast narrow SCSI-2 and fast
wide SCSI-2 interfaces. In each interface, single-ended or
differential can be selected. Furthermore, models with various types
of sector sizes can be chosen from, and a dual-port feature is
available dependant on the user's requirements.

Drive Features
--------------
Newly designed Disk Encloure

Large 3.1 or 2.1 GB storage capacity (formatted)

Lightweight rotary actuator

Advanced MR head

Sputtered media

Fast positioning time - 10.5/9.8 ms (average)

500,000 power-on hour MTBF

SCSI Features
-------------
SCSI-2 command set

10 MB/s fast SCSI-2

Single-ended and differential SCSI

Programmable 512 KB multi-segmented buffer

30 MB/s buffer throughput

Downloadable firmware

Read-ahead cache

Write cache

Defective block slipping

Tagged command queing (Max. 128 commands)

Reed Solomon ECC with "On-the-fly" correction

ANSI X3.131-1986, CCS 4B, X3T9.2-375R Rev. 10K and X3T9.2 855D
Rev. 12 compatibility

Programmable block size: 180 to 4,160 byte/block

Media Defects
-------------
All media defects found during manufacture are mapped out during the
factory format process, so the drive will appear defect free to the
user when first shipped. Any media defects that occur once the drive
is installed should be marked as such by the operating system.
Consult the system documentation for details of any defect management
schemes available.













TOP
previous page: Hard Drive: FUJITSU: M2724TAM 1632MB 2.5"/SSL   ATA3
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M2903QAM 2100MB 3.5"/HH    SCSI2 WIDE