lotus

previous page: Hard Drive: FUJITSU: M2246C 135MB 5.25"/FH   ESDI
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M2246S 130MB 5.25"/FH   SCSI1 SE

Hard Drive: FUJITSU: M2246E 135MB 5.25"/FH ESDI




M 2 2 4 6 E    FUJITSU
NO MORE PRODUCED                                      Native|  Translation
                                                      ------+-----+-----+-----
Form                 5.25"/FH              Cylinders     823|     |     |
Capacity form/unform   135/  171 MB        Heads          10|     |     |
Seek time   / track  25.0/ 5.0 ms          Sector/track     |     |     |
Controller           ESDI                  Precompensation
Cache/Buffer               KB              Landing Zone
Data transfer rate    1.250 MB/S int       Bytes/Sector      512
                            MB/S ext
Recording method     RLL 2/7                        operating  | non-operating
                                                  -------------+--------------
Supply voltage     5/12 V       Temperature *C         5 45    |    -40 60
Power: sleep              W     Humidity     %        20 80    |      5 95
       standby            W     Altitude    km            3.000|        12.000
       idle               W     Shock        g         2       |     20
       seek               W     Rotation   RPM      3600
       read/write    30.0 W     Acoustic   dBA        45
       spin-up            W     ECC        Bit
                                MTBF         h      30000
                                Warranty Month
Lift/Lock/Park     YES          Certificates

Layout

FUJITSU M224XC/E DISK DRIVES OEM MANUAL B03P-4805-0102A...04

  +---------------------------------------------------------+
  |  **** FLT                  16-------+                   |XX 20P
  |  3210      ++RV1            +--CNH5-1                   |XX Card
  |            ++                             16-------+    |XX edge
  |                                            +-CNH7--1    |XX
  |                                                         |XX
  | 16--------16------+                 16-------+          |
  |  +-CNH2--1+-CNH1--1     ++RV2        +-CNH6--1          |XX 34P
  |                         ++                              |XX Card
  |                            10------+                    |XX edge
  |                             +CNH4--1                    |XX
  |++RV3                                 +----+ Terminator  |XX
  |++                 ++                 | M35|+--------+   |XX
  |                   ++RV5              |    |+--------+   |XX
  |                   ++                 +----+             |XX
  |                   ++RV4              LSI *1             |
  |    10-------+                                           |XX Power
  |     +-CNH3--1                                           |XX card
  +---------------------------------------------------------+   edge

*1: Identify that the LSI(M35) is MB447T071.

Jumpers

FUJITSU M224XC/E DISK DRIVES OEM MANUAL B03P-4805-0101A...04

Jumper Setting
==============

Short plugs are inserted as follows when shipped from the factory.

 CNH7: Between 1 and 2, 7 and 8, 9 and 10, 11 and 12, and 15 and 16
       (M224XE Type)

CNH7: Between 1 and 2, 7 and 8, 9 and 10, and 11 and 12 (M224XC Type)

CNH6: Between 1 and 2, and 15 and 16 (M224XE Type)

CNH6: Between 1 and 2 (M224XC Type)

CNH5: Between 11 and 12, and 15 and 16

CNH4: Between 3 and 4

CNH2: Between 15 and 16

The following settings are model specific.

 CNH7: Between 3 and 4:                            M2246
       Between 5 and 6:                            M2245
       No short plugs between 3 and 4, or 5 and 6: M2244

 +-------------------------------------------------------------------+
 | LSI *1 Identify that the LSI(M35) is MB114T071. See Appendix which|
 | describes the Short plugs setting in case that the LSI is         |
 | MB113T047.                                                        |
 +-------------------------------------------------------------------+

 CNH5  Installation Direction
 ----------------------------
       11-12  CLOSED
       13-14  OPEN    Direction type B
       -------------------------------
              OPEN
              CLOSED  Direction type A or C

                  Type A          Type B     Type C
                +--------+       +-+             +-+
                |        |       | +----+   +----+ |
              +-+--------+-+     | |    |   |    | |
              +------------+     | |    |   |    | |
                                 | +----+   +----+ |
                                 +-+             +-+

 CNH5  Ready LED lighting conditions
 -----------------------------------
       15-16  OPEN    Drive select signal not gated
              CLOSED  Drive select signal gated

CNH6 Drive Select
------------------

  +----------------------------------------------------------------+
  |                                 CNH6                           |
  +--------------+------+------+------+------+------+------+-------+
  | Drive Number | 1-2  | 3-4  | 5-6  | 7-8  | 9-10 | 11-12| 13-14 |
  +--------------+------+------+------+------+------+------+-------+
  |      1       |CLOSED|OPEN  |OPEN  |OPEN  |OPEN  |OPEN  | OPEN  |
  |      2       |OPEN  |CLOSED|OPEN  |OPEN  |OPEN  |OPEN  | OPEN  |
  |      3       |OPEN  |OPEN  |CLOSED|OPEN  |OPEN  |OPEN  | OPEN  |
  |      4       |OPEN  |OPEN  |OPEN  |CLOSED|OPEN  |OPEN  | OPEN  |
  |      5       |OPEN  |OPEN  |OPEN  |OPEN  |CLOSED|OPEN  | OPEN  |
  |      6       |OPEN  |OPEN  |OPEN  |OPEN  |OPEN  |CLOSED| OPEN  |
  |      7       |OPEN  |OPEN  |OPEN  |OPEN  |OPEN  |OPEN  | CLOSED|
  +--------------+------+------+------+------+------+------+-------+

 CNH6  Radial Option
 -------------------
       Signal gate or not (select signal)

       15-16  CLOSED  No gate (radial)
              OPEN    Gate (daisy)

When pins 15-16 are shorted, the drive output signals (only A cable
signals) are always enabled, regardless of Drive Select signal. With-
out a jumper here, the output signal are enabled only when the drive
is selected.

 CNH7  Motor start control
 -------------------------
                      Function for motor start control from interface:
       01-02  CLOSED  No
              OPEN    Yes

Setting values are valid when the power is on.

 CNH7  Device type selection
 ---------------------------
       03-04  OPEN
       05-06  OPEN    M2244C/E
       -----------------------
              OPEN
              CLOSED  M2245C/E
              ----------------
              CLOSED
              OPEN    M2246C/E

Setting values are valid when the power is on.

 CNH7  Sector mode setting
 -------------------------
       13-14  OPEN
       15-16  OPEN    Drive hard sector (Sector)
       -----------------------------------------
              OPEN
              CLOSED  Controller hard sector (Byte Clock)
              ------------------------------------------
              CLOSED
              OPEN    Controller soft sector (Address Mark Found)

Setting values are valid when the power is on.

CNH7 Sector setting
--------------------

  +-------------------------------------------------+
  |                          CNH7                   |
  +--------------+-------------+------+------+------+
  | Sectors/Track| Bytes/Sector| 7-8  | 9-10 | 11-12|
  +--------------+-------------+------+------+------+
  |     16       |    1304     |OPEN  |OPEN  |OPEN  |
  |     18       |    1159     |OPEN  |OPEN  |CLOSED|
  |     19       |    1098     |OPEN  |CLOSED|OPEN  |
  |     32       |     652     |OPEN  |CLOSED|CLOSED|
  |     34       |     613     |CLOSED|OPEN  |OPEN  |
  |     35       |     596     |CLOSED|OPEN  |CLOSED|
  |     64       |     326     |CLOSED|CLOSED|OPEN  |
  |     65       |     320     |CLOSED|CLOSED|CLOSED|
  +--------------+-------------+------+------+------+

Note: Valid only in hard sector mode.

 DC Power and pin connector assignments
 --------------------------------------
      +------------+   pin 1    +12 VDC
      | 4  3  2  1 |   pin 2    +12 Volts Return
      +------------+   pin 3    + 5 Volts Return
                       pin 4    + 5 VDC

APPENDIX
--------------------------------------------------------------------
In case that the LSI (M35) mounted on the controller PCB is
MB113TZ047, short plugs setting is different from the setting
described below. Only CNH7 Setting is different.

Short circuit setting shipped from the factory.

CNH7: Between 1 and 2, 3 and 4, 9 and 10, and 15 and 16 (M224XE Type)

CNH7: Between 1 and 2, and 9 and 10 (M224XC Type)

The following settings are model specific.

 CNH7: Between 5 and 6:                      M2246C/E
       Between 7 and 8:                      M2245C/E
       No short between 5 and 6, or 7 and 8: M2244C/E

 CNH7  Motor start control
 -------------------------
                      Function for motor start control from interface:
       01-02  CLOSED  No
              OPEN    Yes

 CNH7  Interface Mode
 --------------------
       03-04  CLOSED  Step mode
              OPEN    Serial mode

 CNH7  Device type selection
 ---------------------------
       05-06  OPEN
       05-06  OPEN    M2244C/E
       -----------------------
              OPEN
              CLOSED  M2245C/E
              ----------------
              CLOSED
              OPEN    M2246C/E

 CNH7  Sector mode setting
 -------------------------
       13-14  OPEN
       15-16  OPEN    Drive hard sector (Sector)
       -----------------------------------------
              OPEN
              CLOSED  Controller hard sector (Byte Clock)
              ------------------------------------------
              CLOSED
              OPEN    Controller soft sector (Address Mark Found)

 CNH7  Sectors/Track
 -------------------
       09-10  OPEN
       11-12  OPEN    16 Sectors/Track
       -------------------------------
              OPEN
              CLOSED  32 Sectros/Track
              ------------------------
              CLOSED
              OPEN    64 Sectors/Track

Install

FUJITSU M224XC/E DISK DRIVES OEM MANUAL B03P-4805-0102A...04

Notes on installation
=====================

Drive mounting
--------------

     horizontally             vertically
   +-----------------+   +--+             +--+ +------------------+
   |                 |   |  +-----+ +-----+  | |                  | x
   |                 |   |  |     | |     |  | x+----------------+x
 +-+-----------------+-+ |  |     | |     |  | ||x              x||
 +---------------------+ |  |     | |     |  | ||  x          x  ||
                         |  |     | |     |  | ||    x      x    ||
      x           x      |  |     | |     |  | ||      x  x      ||
 +------x------x-------+ |  +-----+ +-----+  | ||       xx       ||
 +-+------x--x-------+-+ +--+             +--+ ||     x    x     ||
   |       xx        |                         ||   x        x   ||
   |     x    x      |                         || x            x ||
   +---x--------x----+                         |x                x|
     x            x                           x++----------------++x
      UNACCEPTABLE!                                UNACCEPTABLE!

There are three possible installation directions, and the mounting
angle must be 5* from the horizontal.

 +-------------------------------------------------------------------+
 | Only the formats of M224XE and M224XC are different; components   |
 | and equipment specifications are the same.                        |
 +-------------------------------------------------------------------+

Frame structure
---------------
The casting/HDA (signal ground) is electrically isolated from the
mounting brackets (frame ground). If this isolation is to be main-
tained within the system, precautions must be taken. An embossed
structure (or any other structure that does not touch the aluminium
base) be used to prevent the aluminium base from touching the frame
ground (FG). The mounting screws should project no more than 4mm from
the outer wall of the drive mounting bracket.

Connection
----------

                Multi-drive connection

    +-----------+              +---------+
    |           +-A-cable--o---+  DR1    +-DC+
    |           +-B-cable--+---+         +-+ |
    |           |          |   +---------+ | |
    | CONTROLLER|          |               | |
    |           |          |               | |    +--------+
    |           |          |   +---------+ | +----+ Power  |
    |           |          o---+  DR2    +-+-DC---+ supply |
    |           +-B-cable--+---+         +-o +-DC-+        |
    |           |          |   +---------+ | |    +--+-----+
    |           |          |               F |       |
    |           |          |               G |       |
    |           |          |   +T+-------+ | |       |
    |           |          +---+-+DRn    +-+-+       |
    |           +-B-cable------+         +-o----FG---+
    |           |              +---------+
    +-----------+

In serial mode, up to seven drives can be connected. To connect
drives, the A cable (control signals) must be connected in series and
the B cables (R/W signals) in parallel. The termination of control
signals must be performed only at the last drive.

The total control cable length in a multi-drive configuration should
not exceed 3m max.

Spindle Motor
-------------
The disk are turned by a direct-drive DC motor. The motor attains a
very precise rotational speed of 3600 rpm, 1%. This precision is
achieved through a feedback circuit which includes Hall-effect
elements mounted within the motor assembly.

Air circulation
---------------
The head assembly has a closed-loop air recirculation system using
the blower effect of the rotating disks to continuously cycle air
through the recirculation filter. This filter traps any dust
generated inside the enclosure. To prevent negative pressure is the
vicinity of the spindle when the disks begin rotating, a breather
filter is attached. This breather filter also equalizes the internal
air pressure with the atmospheric pressure due to surrounding
temperature changes.

 Cable connector specification
 -----------------------------
  +----------+----------------+-----------------+------------------+
  |Connector |Name            |Spec. No.        |Manufacturer      |
  +----------+----------------+-----------------+------------------+
  |          |Cable           |FCN-767J034-AU/1 |FUJISTU           |
  |          |Connector       |or 88373-3       |AMP               |
  |A cable   |                |or 3463-0001     |3M                |
  |34 pin    +----------------+-----------------+------------------+
  |          |Drive card edge |-----            |-----             |
  |          +----------------+-----------------+------------------+
  |          |Cable           |455-248-34       |Spectra-Strip     |
  |          |                |or 171-34        |Ansley            |
  +----------+----------------+-----------------+------------------+
  |          |Cable           |FCN-767J020-AU/1 |FUJISTU           |
  |          |Connector       |or 88373-6       |AMP               |
  |B cable   |                |or 3461-0001     |3M                |
  |20 pin    +----------------+-----------------+------------------+
  |          |Drive card edge |-----            |-----             |
  |          +----------------+-----------------+------------------+
  |          |Cable           |455-248-20       |Spectra-Strip     |
  |          |                |or 171-20        |Ansley            |
  +----------+----------------+-----------------+------------------+
  |          |Cable Connector |1-480424-0       |AMP               |
  |          +----------------+-----------------+------------------+
  |Power     |Drive Connector |350211-1         |AMP               |
  |cable     +----------------+-----------------+------------------+
  |(AMP type)|Contact         |170121-4         |AMP               |
  |          +----------------+-----------------+------------------+
  |          |Cable           |AWG 18 (+ 5V RTN)|----              |
  |          |                |AWG 15 (+12V RTN)|                  |
  +----------+----------------+-----------------+------------------+
  |          |Fasten recept-  |62187-1          |AMP               |
  |          |acle for cable  |                 |                  |
  |SG cable  |side            |                 |                  |
  |          +----------------+-----------------+------------------+
  |          |Fasten tab for  |61761-2          |AMP               |
  |          |the drive       |                 |                  |
  |          +----------------+-----------------+------------------+
  |          |Cable           |AWG 20           |                  |
  +----------+----------------+-----------------+------------------+

Options
-------
The M1054A intelligent disk controller that can control four M224XC/E
drives is available as an option. The M1054A11 controller option can
be used by mounting it directly on the M1054A.

For further specification details, refer to M1054A INTELLIGENT DISK
CONTROLLER OEM MANUAL Document code: B05P-2180-0401A.

  +---------------------------+-------------------+------------------+
  |Controller                 | Specification     | Remarks          |
  +---------------------------+-------------------+------------------+
  |M1054A microdisk controller| B05B-2180-B401A   |                  |
  +---------------------------+-------------------+------------------+
  |M1054A11 controller option | B052180-H401A     | M4 mounting screw|
  +---------------------------+-------------------+------------------+
  |M1054A11 controller option | B05B-2180-H401A#N | #6-32UNC mounting|
  |                           |                   | screw            |
  +---------------------------+-------------------+------------------+

Features

FUJITSU M224XC/E DISK DRIVES OEM MANUAL B03P-4805-0102A...04

 Introduction
 ------------
 +-------------------------------------------------------------------+
 | To make system design easier for the user, a simple host inter-   |
 | face controller board based on SCSI is now available as an option.|
 | The drive interface is an Enhanced Small Disk Interface (ESDI),   |
 | with high data integrity and intelligent diagnosis. It has        |
 | superior freedom in sending self-recognition data, and in         |
 | structuring systems.                                              |
 |                                                                   |
 | In addition to the M224XE, the M224XC model, handling the M1054A  |
 | controller format is also available.                              |
 +-------------------------------------------------------------------+
 +-------------------------------------------------------------------+
 | The optional SCSI interface controller board lightens the host    |
 | load in system design. And because the controller board is the    |
 | same shape as the ESDI foot print, it can be mounted on the drive |
 | frame. The drive handling format is mounted on the M224XC.        |
 +-------------------------------------------------------------------+

Media Defects
-------------
Cylinder 0, Head 0 and 1 are defect free.

     M2244C/E....85 or fewer (48 or fewer per surface)
     M2245C/E...120 or fewer (48 or fewer per surface)
     M2246C/E...171 or fewer (48 or fewer per surface)

The maximum defect length is 32 bytes.

All defects are recorded on a self-adhering label and on the media
per the ESDI specification.

When the unit leaves the factory, a printed media defect list for
each drive is sent with it. This information is also written into the
media. The defect list is recorded on cylinders 814 and 822.

Fault lamps
-----------
Drive fault states are displayed by the fault lamps (0, 1, 2, 3).

  +------+-----------+-----------------------------------------------+
  | ITEM | Fault lamp| State                                         |
  |      | 3 2 1 0   |                                               |
  +------+-----------+-----------------------------------------------+
  | 01   | x x x o   | Spindle motor revolutions fewer than 90%      |
  |      |           | standard                                      |
  +------+-----------+-----------------------------------------------+
  | 02   | x x o x   | VCM over current                              |
  +------+-----------+-----------------------------------------------+
  | 03   | x x o o   | Initial seek time out                         |
  +------+-----------+-----------------------------------------------+
  | 04   | x o x x   | Write command during Seek operation           |
  +------+-----------+-----------------------------------------------+
  | 05   | x o x o   | +12V/+5V, less than 80% of standard           |
  +------+-----------+-----------------------------------------------+
  | 06   | x o o x   | Offtrack during Write operation               |
  +------+-----------+-----------------------------------------------+
  | 07   | x o o o   | Write Echo check                              |
  +------+-----------+-----------------------------------------------+
  | 08   | o x x x   | Two or more head ICs selected during Write    |
  |      |           | operation                                     |
  +------+-----------+-----------------------------------------------+
  | 09   | o x x o   | Seek time out                                 |
  +------+-----------+-----------------------------------------------+
  | 10   | o x o x   | Guard band detection during Seek operation    |
  +------+-----------+-----------------------------------------------+
  | 11   | o x o o   | Guard band detection in the linear mode       |
  +------+-----------+-----------------------------------------------+
  | 12   | o o x x   | Overshoot check                               |
  +------+-----------+-----------------------------------------------+
  | 13   | o o x o   | Seek command without ONTRACK signal true      |
  +------+-----------+-----------------------------------------------+
  | 14   | o o o x   | Head load signal lost after READY             |
  +------+-----------+-----------------------------------------------+
  | 15   | o o o o   | Read and Write commands simultaneously issued |
  |      |           | or other miscellaneous faults                 |
  +------+-----------+-----------------------------------------------+
  | 16   | x x x     | Invalid or unimplemented command fault        |
  +------+-----------+-----------------------------------------------+
  | 17   | x x   x   | Interface time out fault                      |
  +------+-----------+-----------------------------------------------+
  | 18   | x x       | Command data parity fault                     |
  +------+-----------+-----------------------------------------------+
 o: On
 x: Off
  : Turn on and off

 Note: Reset using Attention Reset command. Items 02 and 03 can only
       be cleared with power off.













TOP
previous page: Hard Drive: FUJITSU: M2246C 135MB 5.25"/FH   ESDI
  
page up: Hard Drive Specs from FUJITSU
  
next page: Hard Drive: FUJITSU: M2246S 130MB 5.25"/FH   SCSI1 SE