PROMISE TECHNOLOGY, INC.
EIDEPRO
Data Bus | 16-bit ISA |
Card Size | Half-length, full-height card |
Hard Drives supported | Four EIDE drives |
Floppy drives supported | Two 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB drives |
CONNECTIONS | |||
Function | Location | Function | Location |
9-pin serial port 1 - external | CN1 | 34-pin cable connector - floppy drive | J3 |
25-pin parallel port - external | CN2 | 16-pin game port | J4 |
40-pin primary IDE(AT) connector | J1 | 10-pin serial port 2 - internal | J5 |
40-pin secondary IDE(AT) connector | J2 | 4-pin connector - drive active LED | J6 |
USER CONFIGURABLE SETTINGS | |||
Function | Label | Position | |
» | Game port enabled | JP2 | Pins 1 & 2 closed |
Game port disabled | JP2 | Pins 2 & 3 closed | |
» | Parallel port I/O address is 378h | JP3 | Pins 13 & 14 closed |
Parallel port I/O address is 278h | JP3 | Pins 14 & 15 closed | |
» | Parallel port IRQ 7 select | JP3 | Pins 16 & 17 closed |
Parallel port IRQ 5 select | JP3 | Pins 17 & 18 closed | |
» | Factory configured - do not alter | JP4/pins 7 & 8 | Closed |
» | Factory configured - do not alter | JP4/pins 10 & 11 | Closed |
BIOS SELECTION | ||
Type | JP2 | |
» | C8000h | Pins 10 & 11, 13 & 14, 16 & 17 closed |
CC000h | Pins 10 & 11, 14 & 15, 16 & 17 closed | |
D8000h | Pins 10 & 11, 13 & 14, 17 & 18 closed | |
DC000h | Pins 10 & 11, 14 & 15, 17 & 18 closed | |
Disabled | Pins 11 & 12, 14 & 15, 17 & 18 closed |
DMA CHANNEL SELECTION | ||
Channel | JP5 | |
1 | Pins 1 & 2, 4 & 5 closed | |
» | 3 | Pins 2 & 3, 5 & 6 closed |
SERIAL PORT 1 ADDRESS SELECTION | |
Setting | JP3 |
COM1 (3F8h) / IRQ4 | Pins 1 & 2, 4 & 5 closed |
COM3 (3E8h) / IRQ4 | Pins 2 & 3, 4 & 5 closed |
Disabled | Pins 2 & 3, 5 & 6 closed |
SERIAL PORT 2 ADDRESS SELECTION | |
Setting | JP3 |
COM2 (2F8h) / IRQ3 | Pins 7 & 8, 10 & 11 closed |
COM4 (2E8h) / IRQ3 | Pins 8 & 9, 10 & 11 closed |
Disabled | Pins 8 & 9, 11 & 12 closed |
PRIMARY IDE CONTROLLER SELECTION | |||
Setting | JP1 | JP2 | |
» | Primary IDE interface enabled | Pins 4 & 5 closed | Pins 7 & 8 closed |
Primary IDE interface disabled | Pins 4 & 5 open | Pins 8 & 9 closed |
SECONDARY IDE CONTROLLER SELECTION | |||
Setting | JP1 | JP2 | |
» | Secondary IDE interface enabled | Pins 2 & 3 closed | Pins 4 & 5 closed |
Secondary IDE interface disabled | Pins 2 & 3 open | Pins 5 & 6 closed |
FLOPPY CONTROLLER SELECTION | ||
Setting | JP4 | |
» | Enabled | Pins 13 & 14, 16 & 17 closed |
Disabled | Pins 14 & 15, 17 & 18 closed |
PARALLEL PORT MODE SELECTION | ||
Setting | JP4 | |
Uni-directional | Pins 1 & 2, 5 & 6 closed | |
» | ECP | Pins 1 & 2, 4 & 5 closed |
EPP | Pins 2 & 3, 5 & 6 closed | |
Disable | Pins 2 & 3, 4 & 5 closed |