PINE TECHNOLOGY
PT-606G
Data bus: | 16-bit ISA |
Size: | Half-length, full-height card |
Hard drive supported: | Two IDE(AT) drives |
Floppy drives supported: | Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
CONNECTIONS | |
Function | Location |
16-pin game port | CN1 |
40-pin IDE(AT) connector | CN2 |
34-pin cable connector - floppy drive | CN3 |
9-pin serial port 1 - external | CN4 |
10-pin serial port 2 - internal | CN5 |
25-pin parallel port - external | CN6 |
2-pin connector - drive active LED | JP2 |
USER CONFIGURABLE SETTINGS | |||
Function | Location | Setting | |
» | IDE(AT) interface enabled | J6 | pins 2 & 3 closed |
IDE(AT) interface disabled | J6 | pins 1 & 2 closed | |
» | Game port enabled | J7 | pins 1 & 2 closed |
Game port disabled | J7 | pins 2 & 3 closed | |
» | Floppy drive interface enabled | J9 | pins 1 & 2 closed |
Floppy drive interface disabled | J9 | pins 2 & 3 closed |
USER CONFIGURABLE SETTINGS (CONTINUED) | |||
Function | Location | Setting | |
» | Hard drive is installed | J10 | pins 1 & 2 closed |
Hard drive is not installed | J10 | pins 2 & 3 closed | |
» | Secure power source is in use by printer (standard current) | JP3 | closed |
Low-end power source is in use by printer (isolate current) | JP3 | open | |
Note: The size and significance of jumper JP1 is unidentified. |
PARALLEL PORT ADDRESS SELECTION | ||||
LPT | Address | J1 | J8 | |
» | LPT1 | 378h | pins 1 & 2 closed | pins 1 & 2 closed |
LPT2 | 278h | pins 1 & 2 closed | pins 2 & 3 closed | |
Disable LPT1 | N/A | pins 2 & 3 closed | pins 1 & 2 closed | |
Disable LPT2 | N/A | pins 2 & 3 closed | pins 2 & 3 closed |
SERIAL PORT ADDRESS SELECTION | ||||||
Port 1 (CN4) | Port 2 (CN5) | J2 | J3 | J4 | J5 | |
» | COM1 | COM2 | pins 1 & 2 | pins 1 & 2 | pins 1 & 2 | pins 1 & 2 |
COM1 | COM4 | pins 1 & 2 | pins 2 & 3 | pins 1 & 2 | pins 1 & 2 | |
COM3 | COM2 | pins 1 & 2 | pins 1 & 2 | pins 2 & 3 | pins 1 & 2 | |
COM3 | COM4 | pins 1 & 2 | pins 2 & 3 | pins 2 & 3 | pins 1 & 2 | |
COM1 | Disabled | pins 2 & 3 | pins 1 & 2 | pins 1 & 2 | pins 1 & 2 | |
COM3 | Disabled | pins 2 & 3 | pins 2 & 3 | pins 2 & 3 | pins 1 & 2 | |
Disabled | COM2 | pins 1 & 2 | pins 1 & 2 | pins 1 & 2 | pins 2 & 3 | |
Disabled | COM4 | pins 1 & 2 | pins 2 & 3 | pins 1 & 2 | pins 2 & 3 | |
Disabled | Disabled | pins 2 & 3 | pins 1 & 2 | pins 2 & 3 | pins 2 & 3 | |
Note: Pins designated should be in the closed position. |