 |
 |
Articles / TULARC / PC info / Hard Disk/Floppy Controller / A-B / |  |
|
|
||||
|
|
|||
|
|
|||
|
||||
|
|
||||
|
   |
|
||
|
IDE-3296 RMC Hard Disk/Floppy Controller Settings and Configuration |
|
||
|
||||
|
|
|
||
|
||||
|
|
|
|
||
|
||
|
|
|
|
||
|
|
||
|
||
|
|
|
|
||
|
||
BIOTEQ
IDE-3296 RMC
|
Data Bus |
32-bit PCI |
|
Card Size |
Half-length, half-height card |
|
Hard Drives supported |
Four IDE (AT) drives |
|
Floppy drives supported |
None |
|
CONNECTIONS | |||
|
Function |
Location |
Function |
Location |
|
40-pin primary IDE(AT) connector |
CN1 |
10-pin connector - paddlecard (optional) |
JP14 |
|
40-pin secondary IDE(AT) connector |
CN2 |
2-pin connector - drive active LED |
LED |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
|
» |
Disk change enabled |
JP13/1 |
Closed |
|
|
Disk change disabled |
JP13/1 |
Open |
|
» |
IDE base address enabled |
JP13/2 |
Open |
|
|
IDE base address disabled |
JP13/2 |
Closed |
|
» |
IDE(AT) interface enabled |
JP13/3 |
Open |
|
|
IDE(AT) interface disabled |
JP13/3 |
Closed |
|
» |
Native mode enabled |
JP15 |
Closed |
|
|
Native mode disabled |
JP15 |
Open |
|
» |
Secondary INT from drive |
JP16 |
Pins 1 & 2 closed |
|
|
Secondary INT from chip |
JP16 |
Pins 2 & 3 closed |
|
» |
Primary INT from drive |
JP17 |
Pins 1 & 2 closed |
|
|
Primary INT from chip |
JP17 |
Pins 2 & 3 closed |
|
PCI INTERRUPT SELECTION FOR PRIMARY IDE DRIVE | ||||
|
Setting |
JP12/1 |
JP12/2 |
JP12/3 |
JP12/4 |
|
INTA (non-inverted) |
Closed |
Open |
Open |
Open |
|
INTA (inverted) |
Open |
Open |
Open |
Closed |
|
INTB (inverted) |
Open |
Open |
Closed |
Open |
|
INTC (inverted) |
Open |
Closed |
Open |
Open |
Note: In normal operation, JP12/4 is closed with primary drive INT14 using INTA. For OPTi54C and Pentium MBD, set JP12/1 closed, selecting non-inverted INTA. | ||||
|
PCI INTERRUPT SELECTION FOR SECONDARY IDE DRIVE | ||||
|
Setting |
JP11/1 |
JP11/2 |
JP11/3 |
JP11/4 |
|
INTB (non-inverted) |
Closed |
Open |
Open |
Open |
|
INTA (inverted) |
Open |
Open |
Open |
Closed |
|
INTB (inverted) |
Open |
Open |
Closed |
Open |
|
INTC (inverted) |
Open |
Closed |
Open |
Open |
Note: In normal operation, JP12/4 is closed with primary drive INT14 using INTA. For OPTi54C and Pentium MBD, set JP12/1 closed, selecting non-inverted INTA. | ||||
|
MISCELLANEOUS TECHNICAL NOTE |
If your system does not recognize PCI INT, remove jumpers JP11 and JP12 and install paddlecard. |
|
|
|
|
 |
|